ZR-1 Net Registry Forums  

Go Back   ZR-1 Net Registry Forums > Search Forums
Reload this Page Search Results
Register FAQ Calendar Today's Posts Search

Showing results 1 to 14 of 14
Search took 0.01 seconds. Search: Posts Made By: kengodfrey
Forum: C4 ZR-1 Technical Postings 06-27-2014
Replies: 8
Views: 2,787
Posted By kengodfrey
Injector problems

I recently changed injectors in 1991 ZR1. Sometimes it cranks fine, runs perfect, and sometimes it sputters out black smoke, and smells like raw gas. I am assuming it is the injectors, but wanted...
Forum: For Sale & Wanted (General) 05-27-2014
Replies: 1
Views: 1,618
Posted By kengodfrey
Windshield replacement

I am looking for a windshield for ZR1, 1991. Does anyone make a replacement? not OEM? Thanks
Forum: C4 ZR-1 Technical Postings 08-25-2012
Replies: 1
Views: 1,919
Posted By kengodfrey
Stock rearend to 4.10

What needs to be changed to switch from stock differential to 4.10? just the ring and pinion, or does the housing need to be changed also? Where is source for Dana 44 parts? Also understand Viper...
Forum: C4 ZR-1 Technical Postings 08-03-2012
Replies: 3
Views: 2,619
Posted By kengodfrey
Injectors

I have a 1991 ZR1, 19,000 miles. I recently replaced my injectors. I intended to buy RCI injectors, made the call and the salesman suggested I buy another brand; stainless steel, and looked same as...
Forum: C4 ZR-1 Technical Postings 03-22-2012
Replies: 6
Views: 1,662
Posted By kengodfrey
Re: injector swap checklist

I just changed my injectors today. One thing you will need that I did not have, is a long T40 Torx for two of the bolts in the plenum. The set of Torx that I bought, were built into a housing that...
Forum: C4 ZR-1 General Postings 03-22-2012
Replies: 2
Views: 727
Posted By kengodfrey
New Injectors

Just installed new injectors on 1991 ZR1 today. Thanks to Marc Haibeck's DVD, everything went well. Just a couple of comments; I thought I had all the tools needed, but found out that a long T40 Torx...
Forum: C4 ZR-1 Technical Postings 08-26-2011
Replies: 5
Views: 4,135
Posted By kengodfrey
Driving ZR 1 in wet weather

I have a 1991 ZR1. After driving it in wet weather,it creates a loud, screeching noise when it starts drying out. Took it to a knowleadgable Corvette mechanic. He told me to continue driving it, the...
Forum: C4 ZR-1 Technical Postings 08-23-2011
Replies: 8
Views: 6,040
Posted By kengodfrey
Re: 1991 zr1

Wow, you nailed all the symptoms! The car runs perfect until it warms up, and thats when the knock starts. The flywheel makes sense; when I push in the clutch, the noise diminishes. I didnt have time...
Forum: C4 ZR-1 Technical Postings 08-23-2011
Replies: 8
Views: 6,040
Posted By kengodfrey
1991 zr1

I have 1991 zr1. It has 19000 miles. It has developed a knocking noise after ir runs about 15 minutes. Mechanic said it was running on 7 cylinders. Could be plug wires or injectors. Any comments are...
Forum: C4 ZR-1 Technical Postings 12-07-2007
Replies: 5
Views: 3,643
Posted By kengodfrey
Re: Bad amps?

My amps went out. I called Bose, they sent me 4 new ones, at $75.00 each, plus shipping. They did not want my old ones. I changed all 4 out in 3 hours. You can get instructions on this site. I bought...
Forum: C4 ZR-1 General Postings 12-07-2007
Replies: 4
Views: 1,251
Posted By kengodfrey
K & N filters

I just bought a 1991 ZR1, and looking for air intake. I keep reading about K & N, but I called them and they dont make air intake for 1991 ZR1. What is everyone using? Who else makes air intakes?
Forum: Corvette Audio/Electronics 11-29-2007
Replies: 17
Views: 6,253
Posted By kengodfrey
Bose Amps Replacement

I have a 1991 ZR 1. Recently, I had problems with sound sytem, making lots of noise. I was told it was the amps, would cost approximately $200 each to replace. I read in this forum you could send old...
Forum: C4 ZR-1 General Postings 06-11-2007
Replies: 4
Views: 1,799
Posted By kengodfrey
Wheels from 1990 Covette

Someone has two OEM rear tires for sale, 315/35/zr17. He says the tires are mounted on 1990 Covette wheels. (Not ZR 1 Wheels) When I looked up 1990 Corvettes, the wheels were only 9.5 inches,...
Forum: Detailing, Cleaning, and Waxing 06-11-2007
Replies: 7
Views: 5,087
Posted By kengodfrey
Rejex for car finish

Has anyone else tried Rejex? I used the claybar on my vette and then applied Rejex. Really has a really good shine. I had previously used Zaino, but this is much less work and last longer.
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT -4. The time now is 04:49 AM.

Contact Us - ZR-1 Net Registry - Archive - Privacy Statement - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright ZR-1 Net Registry 2025