ZR-1 Net Registry Forums  

Go Back   ZR-1 Net Registry Forums > Search Forums
Reload this Page Search Results
Register FAQ Calendar Today's Posts Search

Showing results 1 to 14 of 14
Search took 0.00 seconds. Search: Posts Made By: TheLurker
Forum: C4 ZR-1 Technical Postings 11-29-2010
Replies: 70
Views: 18,413
Posted By TheLurker
Re: 90 ZR1: Oh crud, did I break it?

I emailed you GTO but have not heard back from you.

Jim
Forum: C4 ZR-1 General Postings 08-14-2010
Replies: 17
Views: 3,968
Posted By TheLurker
Re: Paul Dehnert has passed away.

Paul was one of the nicest, most kind gentlemen you will ever meet. I had nothing but admiration for him and loved to visit with him. He will be missed by many.
Forum: C4 ZR-1 Technical Postings 04-08-2009
Replies: 11
Views: 3,726
Posted By TheLurker
Re: Hey Pete... want to time my cams?

You can do it but it is a pain. You will need the crank position pin as well as the cam pins, a piston stop to zero the timing wheel, and a dial guage. I used to have a paper timing wheel that I...
Forum: C4 ZR-1 Technical Postings 04-08-2009
Replies: 8
Views: 4,278
Posted By TheLurker
Re: Chain Wear Guide strips

Just curious, why do you need them? Once they wear in they hold tension better and are quieter than brand new ones. I have run across two motors where one of the tabs on a strip has broken and the...
Forum: C4 ZR-1 Parts For Sale / Wanted 12-14-2008
Replies: 8
Views: 1,480
Posted By TheLurker
Re: For Sale: New 402 Crank

Yes.
Forum: C4 ZR-1 Parts For Sale / Wanted 12-11-2008
Replies: 8
Views: 1,480
Posted By TheLurker
Re: For Sale: New 402 Crank

This is a Jerry Crews crank, the same ones as LPE uses except they have a slightly bigger stroke to get 415 cubic inches.
Forum: C4 ZR-1 Parts For Sale / Wanted 12-11-2008
Replies: 8
Views: 1,480
Posted By TheLurker
For Sale: New 402 Crank

I have a new 402 crank for sale. This is a crank from the same manufacturer that LPE uses. Long term unemployment forces the sale. Price is $2500.00.
Forum: C4 ZR-1 Technical Postings 06-10-2006
Replies: 1
Views: 1,507
Posted By TheLurker
Re: Factory Camshaft timing procedure

They used pins and had a fixture that actually locked in two holes on the venier and then were able to tighten the cam bolt to the required torque.
Forum: C4 ZR-1 Technical Postings 04-26-2006
Replies: 10
Views: 3,687
Posted By TheLurker
Re: Cam Cover Sealant

Black goes with any color. Just don't paint your engine black. It gets lost in there if you do. Also, some hot tips for you when painting (or powder coating) is to get bits done that you see such as...
Forum: C4 ZR-1 Technical Postings 04-24-2006
Replies: 10
Views: 3,687
Posted By TheLurker
Re: Cam Cover Sealant

I'm just finishing a yellow engine and it looks killer. It has taken over as my newest favorite engine color if it goes with the car.
Forum: C4 ZR-1 Technical Postings 04-19-2006
Replies: 9
Views: 3,077
Posted By TheLurker
Re: LT5 INTERNAL NOISE

Anyone who has heard a rod bearing go should be able to tell you. Many times when one goes you will hear a high pitched squeel as the bearing rotates around the crank. Otherwise, you will hear a low...
Forum: C4 ZR-1 Technical Postings 04-14-2006
Replies: 12
Views: 9,751
Posted By TheLurker
Re: cam timing

I did a thing on cam timing a few years ago. Depending on year, it can move dramatically. Early models (375 hp) with one flat on the venier can swing easily 6 degrees either way. Later models with...
Forum: C4 ZR-1 Technical Postings 01-28-2006
Replies: 36
Views: 8,076
Posted By TheLurker
Re: Update on injectors

The hot tip about cleaned stock injectors is that they tend to stick a bit after cleaning and sitting a while. The best way do do it is to install them and run the car the same day. Before installing...
Forum: C4 ZR-1 Parts For Sale / Wanted 09-04-2005
Replies: 38
Views: 11,981
Posted By TheLurker
I need the mount for the computer that goes...

I need the mount for the computer that goes between the brake booster and the firewall. It has four holes for the booster bolts to slide through. The plastic ECM tray mounts on this piece.
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT -4. The time now is 11:47 PM.

Contact Us - ZR-1 Net Registry - Archive - Privacy Statement - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright ZR-1 Net Registry 2025