03-31-2008 | #1 |
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Digging back into her!!
Dropped the exhaust today in anticipation of the arrival of the B&B thats on its way. Also replaced the output shaft seal & ordered a new speedometer sensor from Bill B.
(THE NAPA SEAL # IS 18992) On the KL YUK!! The real dirty spot is where the tranny has been leaking for a while When I get the new system on I'll take some more pics of it installed. Till then, I'll be cleaning the undercarrige.
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] Last edited by 32valvZ; 03-31-2008 at 10:54 PM. |
03-31-2008 | #2 |
Join Date: Oct 2005
Location: Candy Apple...yUmMy
Posts: 1,137
|
Re: Digging back into her!!
Havin fun yet...nice lift!?!? Yer gonna luv that B&B!
__________________
[IMG]http://i43.photobucket.com/albums/e396/ry368/Zr1launch/Goodfellas-1.gif[/IMG] Here, let me help you with your Vette...lol! [B]1991 QuAsAr BlUe Zr1 w/415 1967 Nova w/Sb2 power!!! 1991 GMC Syclone [/B][FONT=Century Gothic][COLOR=blue] [/COLOR][/FONT] |
03-31-2008 | #3 | |
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Re: Digging back into her!!
Quote:
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] |
|
03-31-2008 | #4 |
Join Date: Oct 2004
Location: Folsom CA
Posts: 1,654
|
Re: Digging back into her!!
Welcome to my world.
I just spent the last two weeks under mine replacing the transmission. Your lift would have come in very handy, I just used jackstands. What a PITA getting the car up high enough to work on it. How much was the lift and what kind is it? TomC
__________________
TomC '90ZR1 #792 Honorary Pirate [B]If it ain't FUN, you're doing something terribly WRONG. [/B] |
04-01-2008 | #5 |
Join Date: Aug 2006
Location: Edmonton, Alberta or Phoenix, Arizona
Posts: 2,741
|
Re: Digging back into her!!
you didn't lie. that's a leak all right, sounds like you got it handled .
__________________
There are no limit's mans ingenuity, just as mans ingenuity will never conquer the forces & behavior of this planet...Smokey Y. |
04-01-2008 | #6 | |
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Re: Digging back into her!!
Quote:
Its a Kwiklift and it was $1,600. shipped with an extra lift bridge!! Heres a link for ya. www.kwiklift.com
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] |
|
04-01-2008 | #7 |
Guest
Posts: n/a
|
Re: Digging back into her!!
Nice garage....love it and gotta get me one of those Kwiklifts. Shipping to Hawaii will probably cost me more than the lift. Just kidding, quoted $200 and might have to jump on that soon. Thanks for sharing.
|
04-01-2008 | #8 |
Join Date: Dec 2004
Location: Jacksonville, FL USA
Posts: 4,645
|
Re: Digging back into her!!
Nice diggs John!
Man that seal was leaking a good bit. I hope this project goes smooth for ya! Definition of a ZR-1: A fiberglass linned hole in the road into which you pour money. Tom
__________________
1990 ZR-1, Black/grey, #2233, stock. ZR-1 Net Reg Founding Member #316 & NCM member |
|
|