Anyone changed their injectors themselves? - ZR-1 Net Registry Forums

crazey · 11 Hours Ago

How much of a pain in the *** is it? I've watched videos, and it seems pretty simple and straight forward. But how many people have done it, and from experience, is it simple or is it a pain?

Thank you

Subfixer · 6 Hours Ago

No hard. Just have to take your time and be careful not to nick any of the rings.

Sent from my Pixel 4a (5G) using ZR-1 Net Registry mobile app

Subfixer · 6 Hours Ago

"o-rings"

Sent from my Pixel 4a (5G) using ZR-1 Net Registry mobile app

Gunny · 2 Hours Ago

fairly straight forward ... don't be in a hurry. search the forum ... a set of diy instructions has likely been posted. if so, it is likely an older post but relevant, nevertheless.

tccrab · 59 Minutes Ago

It's a rite of passage for any and all ZR-1 owners.
It's surprisingly easy to do but depressingly easy to mess up.

Be prepared, have all the necessary tools handy, and, Take. Your. Time.
Do not get in a rush.
Take lots of pictures.
Sketch drawings of what you see as you take it apart.
Pretty sure there's YouTube videos you can and should watch before you get busy.

Be prepared to have to wait a week or two to put it back together.
Take the time to identity everything under the Plenum and get to know what each and everything does.
For some odd reason mice and rats seem to gravitate to setting up housekeeping under the plenum.
Be prepared to call Jerry's Parts if anything looks chewed or ugly.
Check every nut, bolt and fitting.
The air box bolts have a tendency to work their way loose, nows the best time to address that.
Vacuum hoses are now 30 years old.
Don't act surprised if they've gotten soft or brittle.
Test everything, especially everything associated with the secondaries actuators and all the plumbing.
If you're in a no smog state/country/county, I'd highly recommend deleting the secondaries all together. You will need a special tune if you do, Marc Haibec has the appropriate Prom.
As long as you're not in the Arctic, bypassing the throttle body coolant is a simple and cheap mod that will save your plenum and throttle body paint from blistering later on.
Clean out under the coil packs and check the block drain hole at the back. You should never actually need it because you should never get water under the Plenum, but you should be sure that its clear if you should need it.
This is also the *best* time to address the finish on the plenum and injector housings.
Marc Haibec can sell you the correct color paint, or he can arrange to port your plenum and powder coat it. To do this right you have to remove the injector housings and the cam covers too (much more difficult task, especially the passenger side). Marc isn't the only person doing this, there are a small handful of people here who can and will do this for you. Do a little research, dig through Dynomite's Solutions pages here on the forums, it's all there.

Good luck!!

Don't hesitate to post if you have any questions, or run into difficulties.

Crabs

11 Hours Ago	#1
crazey Join Date: May 2024 Location: Columbia, SC Posts: 2	Anyone changed their injectors themselves? How much of a pain in the *** is it? I've watched videos, and it seems pretty simple and straight forward. But how many people have done it, and from experience, is it simple or is it a pain? Thank you

6 Hours Ago	#2
Subfixer Join Date: Sep 2018 Location: Groton, CT Posts: 384	Re: Anyone changed their injectors themselves? No hard. Just have to take your time and be careful not to nick any of the rings. Sent from my Pixel 4a (5G) using ZR-1 Net Registry mobile app __________________ 1992 ZR1 #442, 2 tops, White, White, Haibeck 415, 3.90 gear, Coilovers 2018 Audi RS5, 2.9 V6 Twin Turbo, Auto, Black, Black 2021 Audi Q3, 2.0T, 8 spd Tiptronic, Navarro Blue metallic, Pearl Beige

6 Hours Ago	#3
Subfixer Join Date: Sep 2018 Location: Groton, CT Posts: 384	Re: Anyone changed their injectors themselves? "o-rings" Sent from my Pixel 4a (5G) using ZR-1 Net Registry mobile app __________________ 1992 ZR1 #442, 2 tops, White, White, Haibeck 415, 3.90 gear, Coilovers 2018 Audi RS5, 2.9 V6 Twin Turbo, Auto, Black, Black 2021 Audi Q3, 2.0T, 8 spd Tiptronic, Navarro Blue metallic, Pearl Beige

2 Hours Ago	#4
Gunny Join Date: May 2005 Location: Georgia Mountains Posts: 927	Re: Anyone changed their injectors themselves? fairly straight forward ... don't be in a hurry. search the forum ... a set of diy instructions has likely been posted. if so, it is likely an older post but relevant, nevertheless. __________________ George Jones Founding Member #14 www.zrwon.com

59 Minutes Ago	#5
tccrab Join Date: Oct 2004 Location: Folsom CA Posts: 1,655	Re: Anyone changed their injectors themselves? It's a rite of passage for any and all ZR-1 owners. It's surprisingly easy to do but depressingly easy to mess up. Be prepared, have all the necessary tools handy, and, Take. Your. Time. Do not get in a rush. Take lots of pictures. Sketch drawings of what you see as you take it apart. Pretty sure there's YouTube videos you can and should watch before you get busy. Be prepared to have to wait a week or two to put it back together. Take the time to identity everything under the Plenum and get to know what each and everything does. For some odd reason mice and rats seem to gravitate to setting up housekeeping under the plenum. Be prepared to call Jerry's Parts if anything looks chewed or ugly. Check every nut, bolt and fitting. The air box bolts have a tendency to work their way loose, nows the best time to address that. Vacuum hoses are now 30 years old. Don't act surprised if they've gotten soft or brittle. Test everything, especially everything associated with the secondaries actuators and all the plumbing. If you're in a no smog state/country/county, I'd highly recommend deleting the secondaries all together. You will need a special tune if you do, Marc Haibec has the appropriate Prom. As long as you're not in the Arctic, bypassing the throttle body coolant is a simple and cheap mod that will save your plenum and throttle body paint from blistering later on. Clean out under the coil packs and check the block drain hole at the back. You should never actually need it because you should never get water under the Plenum, but you should be sure that its clear if you should need it. This is also the best time to address the finish on the plenum and injector housings. Marc Haibec can sell you the correct color paint, or he can arrange to port your plenum and powder coat it. To do this right you have to remove the injector housings and the cam covers too (much more difficult task, especially the passenger side). Marc isn't the only person doing this, there are a small handful of people here who can and will do this for you. Do a little research, dig through Dynomite's Solutions pages here on the forums, it's all there. Good luck!! Don't hesitate to post if you have any questions, or run into difficulties. Crabs __________________ TomC '90ZR1 #792 Honorary Pirate [B]If it ain't FUN, you're doing something terribly WRONG. [/B]