WTB: Differential Center Section w/Batwing - ZR-1 Net Registry Forums

BlackZR1 · 03-14-2018

Looking for a nice core with side shafts to build a 4.10
Prefer to keep my low mileage unit intact.
A recycler near me has one but he won't get around to pulling it for a few weeks so though I would check with you guys to see if you know of one with known history, no cracks, etc.

Thanks,
Roger

Ccmano · 03-14-2018

Have you talked to Mirrock Corvette in Saltsburg, PA. ? Good guy. He parting out Z right now...
H

BlackZR1 · 03-14-2018

Yes, that is the guy I have been talking to. He already sold Johnny5's rear.
He only has a 120k miler from a car with front end damage. He said he is not going to bring it inside and start taking it apart for another few weeks. He is about 1.5 hrs from me so he is my backup plan.

Thanks,
Roger

BlackWidow#2 · 03-18-2018

I have one and I'm local. I'll send you a pm.
George

Ccmano · 03-19-2018

Quote:

Originally Posted by BlackWidow#2

I have one and I'm local. I'll send you a pm.
George

I highly recommend George. Great to work with! I bought a trans from him.
H

BlackZR1 · 03-19-2018

I can't believe George lives only 20 miles from me.
Unfortunately his rear is a 4.56 and I am looking to build a 4.10. It is low mileage, freshly set up and fairly priced but it wouldn't be cost effective for me to use it as a core.

My backup plan is Vettepros in Charlotte. They have a '94 diff from a C4 that was not wrecked, just engine damage. My son is passing through there next week on business and can pick it up for me. Not sure when I can get it from him though...

BlackWidow#2 · 03-20-2018

Quote:

Originally Posted by Ccmano

I highly recommend George. Great to work with! I bought a trans from him.
H

Thank you for the recommendation, George

WVZR-1 · 03-20-2018

Quote:

Originally Posted by BlackWidow#2

Thank you for the recommendation, George

Is your 4.56 a Super 44 build or an earlier build using a D44 and specialty bearings/sleeves etc. A quick check would be the size of the pinion nut.

An earlier build using D44 stuff would have a 1 1/8 hex and a Super 44 'vette/viper/C4 despite what folks think is actually spec'd at 1 9/32.

There might be an interested fellow here in the Eastern Panhandle of WV interested.

BlackWidow#2 · 03-20-2018

It's a super 44. I am very familiar with what you are talking about. This is not junk.
Thanks, George

WVZR-1 · 03-20-2018

Quote:

Originally Posted by BlackWidow#2

It's a super 44. I am very familiar with what you are talking about. This is not junk.
Thanks, George

Wasn't implying 'junk' - I've bought/sold a couple very good very early builds with the sleeves and a D44. One was 'beat on' quite regularly and took every thing it was dealt! That was a 3.90 build.

Dropped you a PM!

-Dave

03-14-2018	#1
BlackZR1 Join Date: Aug 2015 Location: Pittsburgh, PA Posts: 152	WTB: Differential Center Section w/Batwing Looking for a nice core with side shafts to build a 4.10 Prefer to keep my low mileage unit intact. A recycler near me has one but he won't get around to pulling it for a few weeks so though I would check with you guys to see if you know of one with known history, no cracks, etc. Thanks, Roger __________________ Roger 1990 ZR-1 #2699 Black on Black 15,000 miles Full-time secondaries, 4.10 gears, C-beam plates, ported top end

03-14-2018	#3
BlackZR1 Join Date: Aug 2015 Location: Pittsburgh, PA Posts: 152	Re: WTB: Differential Center Section w/Batwing Yes, that is the guy I have been talking to. He already sold Johnny5's rear. He only has a 120k miler from a car with front end damage. He said he is not going to bring it inside and start taking it apart for another few weeks. He is about 1.5 hrs from me so he is my backup plan. Thanks, Roger __________________ Roger 1990 ZR-1 #2699 Black on Black 15,000 miles Full-time secondaries, 4.10 gears, C-beam plates, ported top end

03-18-2018	#4
BlackWidow#2 Join Date: Feb 2004 Location: Pittsburgh, PA Posts: 149	Re: WTB: Differential Center Section w/Batwing I have one and I'm local. I'll send you a pm. George __________________ [SIGPIC][/SIGPIC]George C 91 Black/Black ZR1, #2 of 8 black widow cars 15 black/red Z06 :hello:

03-19-2018	#6
BlackZR1 Join Date: Aug 2015 Location: Pittsburgh, PA Posts: 152	Re: WTB: Differential Center Section w/Batwing I can't believe George lives only 20 miles from me. Unfortunately his rear is a 4.56 and I am looking to build a 4.10. It is low mileage, freshly set up and fairly priced but it wouldn't be cost effective for me to use it as a core. My backup plan is Vettepros in Charlotte. They have a '94 diff from a C4 that was not wrecked, just engine damage. My son is passing through there next week on business and can pick it up for me. Not sure when I can get it from him though... __________________ Roger 1990 ZR-1 #2699 Black on Black 15,000 miles Full-time secondaries, 4.10 gears, C-beam plates, ported top end

03-20-2018	#9
BlackWidow#2 Join Date: Feb 2004 Location: Pittsburgh, PA Posts: 149	Re: WTB: Differential Center Section w/Batwing It's a super 44. I am very familiar with what you are talking about. This is not junk. Thanks, George __________________ [SIGPIC][/SIGPIC]George C 91 Black/Black ZR1, #2 of 8 black widow cars 15 black/red Z06 :hello:

03-14-2018	#2
Ccmano Join Date: Jun 2006 Location: Sparks, NV Posts: 2,852	Re: WTB: Differential Center Section w/Batwing Have you talked to Mirrock Corvette in Saltsburg, PA. ? Good guy. He parting out Z right now... H __________________ 90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold.