K & B products ? - Page 3 - ZR-1 Net Registry Forums

RussMcB · 10-09-2016

Quote:

Originally Posted by Billy Mild

What are the most reputable rebuild places?

I don't know, but if I had this question...

I'd be tempted to call one of our reputable builder/vendors, such as, Marc or Jerry. My hunch is they have investigated options and may know which ones offer the best results.

Z51JEFF · 10-11-2016

Quote:

Originally Posted by RussMcB

As a side note, the DIY Auto Tune guys told me one of the challenges with their LT-5 ECU is the connectors needed to make it plug-n-play. They're no longer available new and they haven't been able to find anyone to make them for a reasonable cost. That means they have to get them from junk yards. Luckily, there were a few other '90's GM cars that use the same connectors (but not a lot - not that easy to find them in very good condition).

This is a stretch as I'm sure they have checked for connectors but I've used TERMINAL SUPPLY and MOUSER for OEM GM connectors in the past.

-=Jeff=- · 10-11-2016

Quote:

Originally Posted by Z51JEFF

This is a stretch as I'm sure they have checked for connectors but I've used TERMINAL SUPPLY and MOUSER for OEM GM connectors in the past.

when I was querying them about the cmn I ask about connectors..

Their response:

Quote:

We have at least worked out a way to source the connectors used, but it would be good if we found a way to buy them new. A lot of late '80s and early '90s GM products used the same connector.

Z51JEFF · 10-11-2016

Quote:

Originally Posted by -=Jeff=-

when I was querying them about the cmn I ask about connectors..

Their response:

What exactly do the connectors look like?

RussMcB · 10-11-2016

Quote:

Originally Posted by Z51JEFF

What exactly do the connectors look like?

Not a great view, but here's a picture.

I think the part they want is the large female piece that accepts the male plugs.

-=Jeff=- · 10-11-2016

Quote:

Originally Posted by RussMcB

Not a great view, but here's a picture.

I think the part they want is the large female piece that accepts the male plugs.

Correct the 4 main connectors.. I have 2 or 3 L98 ECMs with the same connectors

9T1 Red ZR1 · 10-11-2016

I searched 19152968 and came up with a few sites that claim to have them. This number came from Marc's site as a remanufactured unit. I don't know enough about these to know if this is really what we need for the correct ECM. Is anyone familiar with what this is? Rockauto.com also has a listing for the ECM.

Thanks,
Bill

-=Jeff=- · 10-11-2016

If it is a number on Marc's site then it is correct. If I ordered from anywhere. I would pay the core fee until I knew I had the correct ECM in my possession and it worked..

Sent from my iPhone using ZR-1 Net Registry

10-11-2016	#27
9T1 Red ZR1 Join Date: Jun 2013 Location: Warminster, PA Posts: 78	Re: K & B products ? I searched 19152968 and came up with a few sites that claim to have them. This number came from Marc's site as a remanufactured unit. I don't know enough about these to know if this is really what we need for the correct ECM. Is anyone familiar with what this is? Rockauto.com also has a listing for the ECM. Thanks, Bill __________________ LT5 Red/Red

10-11-2016	#28
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,156	Re: K & B products ? If it is a number on Marc's site then it is correct. If I ordered from anywhere. I would pay the core fee until I knew I had the correct ECM in my possession and it worked.. Sent from my iPhone using ZR-1 Net Registry __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978