shocks

[raymond greene]

I have had a few C4's in the past and nothing rode as hard as this. (85,88,89 and 96GS) There is some dried up oil and grime on the shocks. As original, I am sure they are toast as you say.

[Z06scentair]

Originally Posted by raymond greene

I have had a few C4's in the past and nothing rode as hard as this. (85,88,89 and 96GS) There is some dried up oil and grime on the shocks. As original, I am sure they are toast as you say.

Its possible, you can send them back to bilstein for a rebuild for ~200 each.

[GOLDCYLON]

Suggest here if considering new. http://www.eshocks.com/bil_veh.asp?M...=All&SubChar=Q

$192.00 each cheapest price on the net

When you turn the key to run not start do you see a service ride light ? The fx3 system only illuminates when there is a time error on one of the four corners or a problem with the controller. The time out is normally a gear or an actuator problem. However make sure the light is functional and then go from there

[vilant]

Originally Posted by Z06scentair

Its possible, you can send them back to bilstein for a rebuild for ~200 each.

My shocks are currently at Bilstein. They called the other day and told my they no longer have the rear shock rods and they are no longer available and won't be produced again. So you can only have the front shocks rebuilt now (but that won't last for too much longer).

[mike100]

Originally Posted by vilant

My shocks are currently at Bilstein. They called the other day and told my they no longer have the rear shock rods and they are no longer available and won't be produced again. So you can only have the front shocks rebuilt now (but that won't last for too much longer).

Good to know, I have a pair of fronts i want to have made with a more aggressive valving. If your rods are ok, couldn't they still do them?

I guess i can see them just saying no so as to avoid people from sending them in and then finding out they were no good. I'm local, could just drop them on the back door like i did last time.

[raymond greene]

I have turned the setting knob to all the settings several times to no avail. When starting up the light will come on for a second, then go out. I am sure the shocks are cooked, but I would be surprised if the control on top of the shocks are still good?

[We Gone]

From what you are saying the FX3 system is ok must be just your shocks. This is from a post on CF hope it helps ya.

Originally Posted by c4cruiser

(I originally wrote them and they are taken from the FX3 section in the FSM)


FX3 Diagnostics
To clear FX3 codes, turn the ignition to Run but don't start the engine. With a small paperclip, jump pins A and C on the ALDL (in the upper left corner of the driver' side knee bolster). These pins are on the upper row and are lettered in this fashion as you look at them: E D C B A
To clear the codes, you must jump the pins for two seconds doing it for a total of three times.
To display the codes (which is simply a series of flashes of the SRC message) jump the pins and turn the ignition to Run and watch the SRC message lamp.
Codes are two digit values and the sequence always begins and ends with a code "12". The SRC light flashes based on each integer of the code and the code repeats three times with a couple of seconds between each code value. For example a Code 12 flashes like this:
12= blink, blink - blink / blink, blink - blink / blink, blink - blink
(there is a about a half second "/" pause between each of the three code intergers)
A code 32 is:
32= blink, blink, blink - blink, blink (and repeats twice more)
After all of the codes have been displayed there is a final code 12 and the sequence repeats until you either pull the jumper or turn the ignition off
Here’s the code meanings:
Code 12 = Start of sequence
Code 13 = Left Rear Time Out (possible broken gear on shock rod)
Code 14 = Right Front Time Out (same)
Code 21 = Left Front Time Out (same)
Code 22 = Right Rear Time Out (same)
Code 23 = Loss of vehicle speed signal (this code will appear if the ignition switch is cycled On/OFF three times without the vehicle moving. Once the vehicle moves and there are no other codes the SRC light will go OFF but this code remains in history)
Code 31 = Left Front Out of Position (possible bad actuator)
Code 32 = Right Front Out of Position (same)
Code 33 = Left Rear Out of Position (same)
Code 34 = Right Rear Out of position (same)
Code 41 = SRC Switch short to Voltage
Code 42 = SRC Switch open contacts (console switch not positioned at one of the three detents
Code 43 = SRC switch circuit open.
Give this a try and report what codes you get. Remember, a Code 12 starts the sequence and also ends it. Any other codes are repeated three times before the next code is displayed.