![]() |
#31 |
Join Date: Apr 2010
Location: O'Fallon, Mo
Posts: 733
|
![]() ![]() this is the test bed. It will have a supra 3:12 independent rear setup, zf trans and stock lower lt-5. It will be run on a haltech 2000 platinum with ls1 coils. God save the queen |
![]() |
![]() |
![]() |
#32 |
![]() Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,157
|
![]()
COOL Project
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
![]() |
![]() |
![]() |
#33 | |
Join Date: Apr 2010
Location: O'Fallon, Mo
Posts: 733
|
![]() Quote:
I may wind up going over the ems with him, and leaving the car with him for him to piddle with, and it would give everyone an independent source. I dunno exactly how it is all going to unfold in the long run, right now he is just helping me get it all together since I have limited time |
|
![]() |
![]() |
![]() |
#34 |
![]() Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,157
|
![]()
Cool Deal. That mean you will be in Chi-town tomorrow too then?
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
![]() |
![]() |
![]() |
#35 |
Join Date: Apr 2010
Location: O'Fallon, Mo
Posts: 733
|
![]() |
![]() |
![]() |
![]() |
#36 |
![]() Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,157
|
![]()
Ah sorry I thought you were here tomorrow..
Either way, Have a safe trip to meet him..
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
![]() |
![]() |
![]() |
#37 |
Join Date: Apr 2010
Location: O'Fallon, Mo
Posts: 733
|
![]() |
![]() |
![]() |
![]() |
#38 |
![]() Join Date: Nov 2007
Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri
Posts: 6,466
|
![]() |
![]() |
![]() |
![]() |
#39 |
![]() Join Date: Jan 2004
Location: Enterprise, Alabama
Posts: 356
|
![]()
Any updates to this Water/ Meth Injection test?
![]() |
![]() |
![]() |
![]() |
#40 |
![]() Join Date: Jan 2004
Location: Enterprise, Alabama
Posts: 356
|
![]()
Okay guys I finally installed my Snow Performance Water Meth Injection system on my LT5. I have done my homework on the benefits, listen to the nay sayers.... heard that it is only for boosted vehicles etc. (What is a boosted vehicle but another means to increasing compression thus power.)
I ran my car WOT with it on and with it off. I will say I can definitely tell seat of the pants feel that there is more power with it on. Engine mods are: ported heads, stage 1 cams, secondaries removed and Haibeck tune. Even though there is a little more power to be gained with an advancement in timing, or at least I have heard but not sure on LT5s. I decided not to tweak timing in the event I run low on boost juice. My thinking is the benefits of a cool intake charge, cleans my pistons and allows my motor to give everything it has without the timing being retarded due to detonation. Below are pics on where I installed the pump and injector. Just thought I would share what I have done. ![]() ![]() Located the pump on floor, I used the stock C4 radiator overflow container. Painted it black crinkle and plummed it for the juice. It holds 1 gallon of boost juice. ![]() You will notice that I installed a on-off switch to the pump. This lets me test the system lights and switches and prevents it from coming on if I don't want it to. ![]() Installed switches just below dash with power on LED (green). Red LED is my activation light. ![]() Vacuum activation switch fits nicely into fender and vacuum source to manifold. ![]() Tapped IAT port for injection of Meth and covered it to look factory.
__________________
Tony Davila (Projects) Water Meth: http://www.zr1.net/forum/showthread.php?t=19422 Exhaust cut outs: http://www.zr1.net/forum/showthread.php?t=22689 Auxiliary 12V install: http://www.zr1.net/forum/showthread.php?t=22878 Auxiliary pusher fan install: http://www.zr1.net/forum/showthread.php?t=22859 Oil Catch can Project: http://www.zr1.net/forum/showthread.php?t=20320 Last edited by Tony Davila; 01-22-2013 at 06:11 PM. |
![]() |
![]() |
![]() |
|
|