Accel & Multec Injector ??? - ZR-1 Net Registry Forums

32valvZ · 01-31-2008

Got all my parts in today (thanks Jeff) & see theres a difference in the factory injectors & the Accels. The primaries on the Multecs dont have an O ring on the tips & look different from the secondaries which DO have an O ring.

The Accels look exactly the same & both have O rings. Do I remove the O rings or leave them on (primary side of course)?

kenthompson · 01-31-2008

Well, I don't know if it was right or not, but the Accels I put in, I just put them in. O-rings and all.

Now somebody's going to tell me I have to take it back apart. :P

KT

flyin ryan · 01-31-2008

on 92's & up you shouldn't need to do anything concerning O-rings with the Accel's, individual pt. no: 150121 or eight pack no: 150821. you might need to use a razor blade to remove the plastic guide for the injector harness clip. it's just a guide, the harness will still clip in place by using the tabs on the sides. the guide was so the primary & secondary were not swapped.

32valvZ · 01-31-2008

The part # is 150821 for all 16. 2 8-pack boxes. The original primaries had no O rings, these all have O rings....Jeff already trimmed the tabs for me, so, no problem there.....

01-31-2008

Throw them in and forget about it. Make sure the C-clip hits the first indentation making sure the injector gets fully seated.

And yes, your coils were trimmed and numbered, as were the tabs for the injectors.

GOLDCYLON · 01-31-2008

Quote:

Originally Posted by Jeffvette

Throw them in and forget about it. Make sure the C-clip hits the first indentation making sure the injector gets fully seated.

And yes, your coils were trimmed and numbered, as were the tabs for the injectors.

Ive always heard Jeff offers full "trim" service

Aurora40 · 02-01-2008

I don't understand, so you all are saying you leave the spray-end o-ring on the injector? It won't be held in by anything except the o-ring's tension. I'd be afraid one day it might fall off and get sucked into the engine.

I used '93+ injectors and here is what I did to them prior to installing:

32valvZ · 02-01-2008

Aurora, that was my reasoning as well. Thats why I questioned it. I might take them off too, its just my luck & one will fall off.

TonyTZR1 · 02-01-2008

The 1990 primary injector has an "O" ring that sits inside the housing body. The "O" ring fits around the injector body providing the seal. These are about the size of a quarter and no longer available at GM. If you need some let me know I can tell you where to buy them, cost is about a dollar each. These are made of Viton material, same as the original. GM price on these was $25.00 each.

01-31-2008	#1
32valvZ Join Date: Nov 2007 Location: Sunshine State Posts: 1,061	Accel & Multec Injector ??? Got all my parts in today (thanks Jeff) & see theres a difference in the factory injectors & the Accels. The primaries on the Multecs dont have an O ring on the tips & look different from the secondaries which DO have an O ring. The Accels look exactly the same & both have O rings. Do I remove the O rings or leave them on (primary side of course)?

01-31-2008	#2
kenthompson Join Date: Jul 2007 Location: Las Vegas Posts: 298	Re: Accel & Multec Injector ??? Well, I don't know if it was right or not, but the Accels I put in, I just put them in. O-rings and all. Now somebody's going to tell me I have to take it back apart. :P KT

01-31-2008	#3
flyin ryan Join Date: Aug 2006 Location: Edmonton, Alberta or Phoenix, Arizona Posts: 2,736	Re: Accel & Multec Injector ??? on 92's & up you shouldn't need to do anything concerning O-rings with the Accel's, individual pt. no: 150121 or eight pack no: 150821. you might need to use a razor blade to remove the plastic guide for the injector harness clip. it's just a guide, the harness will still clip in place by using the tabs on the sides. the guide was so the primary & secondary were not swapped.

01-31-2008	#4
32valvZ Join Date: Nov 2007 Location: Sunshine State Posts: 1,061	Re: Accel & Multec Injector ??? The part # is 150821 for all 16. 2 8-pack boxes. The original primaries had no O rings, these all have O rings....Jeff already trimmed the tabs for me, so, no problem there.....

01-31-2008	#5
Jeffvette Guest Posts: n/a	Re: Accel & Multec Injector ??? Throw them in and forget about it. Make sure the C-clip hits the first indentation making sure the injector gets fully seated. And yes, your coils were trimmed and numbered, as were the tabs for the injectors.

02-01-2008	#7
Aurora40 Join Date: May 2005 Location: Leesburg, VA Posts: 2,704	Re: Accel & Multec Injector ??? I don't understand, so you all are saying you leave the spray-end o-ring on the injector? It won't be held in by anything except the o-ring's tension. I'd be afraid one day it might fall off and get sucked into the engine. I used '93+ injectors and here is what I did to them prior to installing:

02-01-2008	#8
32valvZ Join Date: Nov 2007 Location: Sunshine State Posts: 1,061	Re: Accel & Multec Injector ??? Aurora, that was my reasoning as well. Thats why I questioned it. I might take them off too, its just my luck & one will fall off.

02-01-2008	#9
TonyTZR1 Join Date: Dec 2007 Location: Cottonwood California Posts: 36	Re: Accel & Multec Injector ??? The 1990 primary injector has an "O" ring that sits inside the housing body. The "O" ring fits around the injector body providing the seal. These are about the size of a quarter and no longer available at GM. If you need some let me know I can tell you where to buy them, cost is about a dollar each. These are made of Viton material, same as the original. GM price on these was $25.00 each.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode