ZR-1 Net Registry Forums  

Go Back   ZR-1 Net Registry Forums > Search Forums
Reload this Page Search Results
Register FAQ Calendar Today's Posts Search

Showing results 1 to 10 of 10
Search took 0.00 seconds. Search: Posts Made By: Merlot566jka
Forum: C4 ZR-1 Technical Postings 01-20-2013
Replies: 117
Views: 34,501
Posted By Merlot566jka
Re: Raptor and Henderson Performance

By "subsystems" did you find a way to communicate with the CCM, ASR and EBTCM?
Forum: C4 ZR-1 Technical Postings 01-08-2013
Replies: 28
Views: 22,951
Posted By Merlot566jka
Re: LS1b (411) PCM Swap

2003 c5 corvette 0411 pcm, pin 14 on the c1 blue connector, tan wire, 800 series UART data for Throttle Actuator Control Serial Data

in the past all 800 series circuits were UART, as is here.
...
Forum: C4 ZR-1 Technical Postings 01-08-2013
Replies: 28
Views: 22,951
Posted By Merlot566jka
Re: LS1b (411) PCM Swap

Jep,

How are you defining the difference between LS1a and LS1b?

From what I have found, They all used UART to connect with the Serial Data link. Either way, I am 99% sure that up until GM-LAN...
Forum: C4 ZR-1 Technical Postings 01-08-2013
Replies: 28
Views: 22,951
Posted By Merlot566jka
Re: LS1b (411) PCM Swap

Jep,

I am still actively working on this, over here... http://forums.corvetteforum.com/c4-tech-performance/3029224-24x-conversion.html#post1582765003

Is the LT5 crank keyed on the nose?
...
Forum: C4 ZR-1 Technical Postings 06-10-2012
Replies: 17
Views: 3,635
Posted By Merlot566jka
Re: Computer fans in inner fender.

Bilge blowers will survive.

What's the purpose of these?
Forum: C4 ZR-1 Technical Postings 06-09-2012
Replies: 28
Views: 22,951
Posted By Merlot566jka
Re: LS1b (411) PCM Swap

EFI connections tried the 24x reluctor wheel on a dampner and they had too much noise on the hall effect for it to work properly. But I have used a 7x that I made and it was bolted on the outside of...
Forum: C4 ZR-1 Technical Postings 06-09-2012
Replies: 28
Views: 22,951
Posted By Merlot566jka
Re: LS1b (411) PCM Swap

Right, the LT5 was a fresh design. I suppose the point I was getting at was the crank reluctor wheel is inthe middle of the crank, like I had thought. This design was used on many other GM vehicles...
Forum: C4 ZR-1 Technical Postings 06-08-2012
Replies: 28
Views: 22,951
Posted By Merlot566jka
Re: LS1b (411) PCM Swap

Hey guys, how does the lt5 get its crank trigger pulse for the icm?

If its a pressed on disc around the crank, look at GMs 3400,3500 v6 engines. They have a large inner diameter wheel with the...
Forum: C4 ZR-1 Technical Postings 06-07-2012
Replies: 24
Views: 5,515
Posted By Merlot566jka
Re: Ignition Impulse @ Balancer/Dampner

Interesting. I do not think this will work on the 411 pcm. the pulses on the 411's reluctor are 12* and 3* (total 15*) and I believe its the trailing edge of the tooth that initiates the trigger. As...
Forum: C4 ZR-1 Technical Postings 06-06-2012
Replies: 28
Views: 22,951
Posted By Merlot566jka
Re: LS1b (411) PCM Swap

Following this, and have borrowed some of your material. And have some to contribute. http://forums.*************.com/c4-tech-performance/3029224-24x-conversion.html#post1581004077

I don't know if...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -4. The time now is 03:12 PM.

Contact Us - ZR-1 Net Registry - Archive - Privacy Statement - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright ZR-1 Net Registry 2025