Quater mile times...

[ffvetteman]

Just wanted to see some of your 1/4 mile times.

If you guys can, include your 60ft times, total MPH and ending speed. Then list what, if any, mods you have. Also curious on you guys that are stock.

Just curious what these beasts can do.

I'll start: ohh wait I dont have one yet :-D

[cward]

#364 1991 Black/Black
11.08@129 1.59 Best 60'
Stock long block
ported inj. housings and plenum
Jeal headers
3" SS exhaust with X pipe no cats or mufflers
Marc Randolph chip
NitrousExpress Gemini

Curtis

[90ZR1]

Are you on a drag radial?

[cward]

I was using 10" ET Streets. To get the 1.59, I had to launch very hard. Lucky not to break anything. The 11.08 was done launching fairly hard and spraying 225.

[ZR-1Mom]

Check them out here.

http://zr1netregistry.com/ZR1_performance.htm

[rkreigh]

this summer ran the car for the first time and did

11.67 @ 124.8 with a 1.88 60 ft time

same car has been

11.48 @ 127 with Phil DeJohn driving it.

if I could drive and put some slicks on I would hope to match that
scorching time curtis made!! that car was way fast and earned quite
a bit of big time performance for the buck.

my car is a
1995 ZR-1, LSV Lingenfelter Super Vette, 390 stroker
ti rods, retainers, big valves, 234 cams, ported heads, top end
headers, B&B with random cats, 4.10 gears

505 rwhp 434 torq with street chip

about 10 more hp with the race chip and good gas.

[90ZR1]

I have just intake/exhaust and drag radials and I'm hoping for a 12.7. I want to do headers ported intake manifold. Nitrous? It is very tempting. Well my goal is to have a 11.9 timeslip.

[GregCrowe]

1991 ZR-1
Flowmaster Cat-Back
DRM Chip
Drag Radials

12.32 @ 114

[Greybeard ZR1]

Best time: 12.06@117mph. - 1.76 60ft. at 80% humid, 75deg.F, alt- 10ft.

Stock engine with these boltons: "Forced air" intake, coplon duct, Demon coils, headers (no cats), 3" B&B's, X pipe, no mufflers, Rippie flywheel, 4.10 gears, BFG Drag Radials (20lbs.).

[Hammer]

Looks like my time last year (2006) was as follows:
60 FT 2.224
330 FT 5.862
660 FT 8.781 @ 84.450
1000 FT 11.281
1/4 13.372 @ 108.06

We're headed out next weekend and have added the Coplon Duct, Haibeck Chip and Flowmaster. Should be better, right.

[bodak1]

1990 Lingenfelter ZR1, 385 cu in, headers, 4.09 gears, bfg drag radials. Was at Muncie Dragstrip in May. 60 ft time was 1.809. Ran 11.605 at 126.97. Best ever was 11.21 and 127.75

[Z Factor]

Hello and welcome to the forum.:handshak:

:cheers:

[jonszr1]

my best 11.88 @ 119.24 1.8860ft 1/87.99@96.21 . corey henderson siamesed ported olenum and inj housings and dyno tune . jeal headers with custom spin tech exhaust. 410 gears with mt et street radials @18 lbsps had weak fuel pumps. new ones in for the 24th

[cuisinartvette]

13.4 @108 or 109, Id have to dig up the slip. 60' a measly 2.2/3. Have to get a tire on it to really lean on it.
Lst pass at Famoso I ran 110 going through the traps, no time from the tower. Apparently something (a bat?) tripped the lights up according to the girl handing them out. Pretty confident with a DR I can get 112 out of it. Oh well..

Stock
4.09
Haibeck tune
Dual 3" straights

[Hammer]

12.817 @ 114.18 at Portland Raceway
2.074 60 Ft

Flowmaster #17115
Haibeck Chip
Coplon Duct
K & N Filter w/ Open Lid
Hurst Shifter