Quater mile times... - ZR-1 Net Registry Forums

ffvetteman · 01-26-2005

Just wanted to see some of your 1/4 mile times.

If you guys can, include your 60ft times, total MPH and ending speed. Then list what, if any, mods you have. Also curious on you guys that are stock.

Just curious what these beasts can do.

I'll start: ohh wait I dont have one yet

cward · 01-26-2005

#364 1991 Black/Black
11.08@129 1.59 Best 60'
Stock long block
ported inj. housings and plenum
Jeal headers
3" SS exhaust with X pipe no cats or mufflers
Marc Randolph chip
NitrousExpress Gemini

Curtis

90ZR1 · 01-27-2005

Are you on a drag radial?

cward · 01-28-2005

I was using 10" ET Streets. To get the 1.59, I had to launch very hard. Lucky not to break anything. The 11.08 was done launching fairly hard and spraying 225.

ZR-1Mom · 01-28-2005

Check them out here.

http://zr1netregistry.com/ZR1_performance.htm

rkreigh · 01-28-2005

this summer ran the car for the first time and did

11.67 @ 124.8 with a 1.88 60 ft time

same car has been

11.48 @ 127 with Phil DeJohn driving it.

if I could drive and put some slicks on I would hope to match that
scorching time curtis made!! that car was way fast and earned quite
a bit of big time performance for the buck.

my car is a
1995 ZR-1, LSV Lingenfelter Super Vette, 390 stroker
ti rods, retainers, big valves, 234 cams, ported heads, top end
headers, B&B with random cats, 4.10 gears

505 rwhp 434 torq with street chip

about 10 more hp with the race chip and good gas.

90ZR1 · 02-06-2005

I have just intake/exhaust and drag radials and I'm hoping for a 12.7. I want to do headers ported intake manifold. Nitrous? It is very tempting. Well my goal is to have a 11.9 timeslip.

GregCrowe · 06-02-2005

1991 ZR-1
Flowmaster Cat-Back
DRM Chip
Drag Radials

12.32 @ 114

Greybeard ZR1 · 06-20-2005

Best time: 12.06@117mph. - 1.76 60ft. at 80% humid, 75deg.F, alt- 10ft.

Stock engine with these boltons: "Forced air" intake, coplon duct, Demon coils, headers (no cats), 3" B&B's, X pipe, no mufflers, Rippie flywheel, 4.10 gears, BFG Drag Radials (20lbs.).

Hammer · 04-15-2007

Looks like my time last year (2006) was as follows:
60 FT 2.224
330 FT 5.862
660 FT 8.781 @ 84.450
1000 FT 11.281
1/4 13.372 @ 108.06

We're headed out next weekend and have added the Coplon Duct, Haibeck Chip and Flowmaster. Should be better, right.

01-26-2005	#1
ffvetteman Join Date: Jan 2005 Location: New Berlin WI Posts: 247	Quater mile times... Just wanted to see some of your 1/4 mile times. If you guys can, include your 60ft times, total MPH and ending speed. Then list what, if any, mods you have. Also curious on you guys that are stock. Just curious what these beasts can do. I'll start: ohh wait I dont have one yet

01-26-2005	#2
cward Join Date: Dec 2004 Location: Luling, TX Posts: 97	#364 1991 Black/Black 11.08@129 1.59 Best 60' Stock long block ported inj. housings and plenum Jeal headers 3" SS exhaust with X pipe no cats or mufflers Marc Randolph chip NitrousExpress Gemini Curtis __________________ Curtis Ward 91 ZR-1 #364 RIP

01-28-2005	#4
cward Join Date: Dec 2004 Location: Luling, TX Posts: 97	I was using 10" ET Streets. To get the 1.59, I had to launch very hard. Lucky not to break anything. The 11.08 was done launching fairly hard and spraying 225. __________________ Curtis Ward 91 ZR-1 #364 RIP

01-28-2005	#5
ZR-1Mom Join Date: Dec 2003 Location: New Hampshire Posts: 49	Check them out here. http://zr1netregistry.com/ZR1_performance.htm __________________ ZR-1 Mom

01-28-2005	#6
rkreigh Join Date: Jan 2004 Location: Alex VA Posts: 1,087	this summer ran the car for the first time and did 11.67 @ 124.8 with a 1.88 60 ft time same car has been 11.48 @ 127 with Phil DeJohn driving it. if I could drive and put some slicks on I would hope to match that scorching time curtis made!! that car was way fast and earned quite a bit of big time performance for the buck. my car is a 1995 ZR-1, LSV Lingenfelter Super Vette, 390 stroker ti rods, retainers, big valves, 234 cams, ported heads, top end headers, B&B with random cats, 4.10 gears 505 rwhp 434 torq with street chip about 10 more hp with the race chip and good gas. __________________ 95 390 LPE ZR1 (505 rwhp) LSV = Lingenfelter Super Vette Twin Turbo 2003 Z06 (800 RWHP)

01-27-2005	#3
90ZR1 Join Date: Oct 2004 Location: Libertyville Posts: 70	Are you on a drag radial? __________________ 1990 Black ZR1 #2910 32k mi. Griff

02-06-2005	#7
90ZR1 Join Date: Oct 2004 Location: Libertyville Posts: 70	I have just intake/exhaust and drag radials and I'm hoping for a 12.7. I want to do headers ported intake manifold. Nitrous? It is very tempting. Well my goal is to have a 11.9 timeslip. __________________ 1990 Black ZR1 #2910 32k mi. Griff

06-02-2005	#8
GregCrowe Join Date: Sep 2004 Location: Oklahoma Posts: 111	1991 ZR-1 Flowmaster Cat-Back DRM Chip Drag Radials 12.32 @ 114

06-20-2005	#9
Greybeard ZR1 Join Date: Jun 2005 Posts: 14	Best time: 12.06@117mph. - 1.76 60ft. at 80% humid, 75deg.F, alt- 10ft. Stock engine with these boltons: "Forced air" intake, coplon duct, Demon coils, headers (no cats), 3" B&B's, X pipe, no mufflers, Rippie flywheel, 4.10 gears, BFG Drag Radials (20lbs.). __________________ 91' ZR1 #1236

04-15-2007	#10
Hammer Join Date: Apr 2006 Location: Ideho Posts: 2,653	Re: Quarter mile times... Looks like my time last year (2006) was as follows: 60 FT 2.224 330 FT 5.862 660 FT 8.781 @ 84.450 1000 FT 11.281 1/4 13.372 @ 108.06 We're headed out next weekend and have added the Coplon Duct, Haibeck Chip and Flowmaster. Should be better, right. __________________ [I][FONT=Comic Sans MS]John Boyd[/FONT][/I] [I][FONT=Comic Sans MS][SIZE=1]Ideho[/SIZE][/FONT][/I] [FONT=Comic Sans MS][SIZE=1][I]2015 ZL1 [/I][I]Camaro #1121 BLACK/BLACK 6 SPD (540 RWHP)[/I][/SIZE][/FONT] [I][FONT=Comic Sans MS][SIZE=1]1991 ZR-1 #458 [COLOR=red]RED/[/COLOR][COLOR=black]BLACK 72[/COLOR]k miles ([B][COLOR=red]SOLD[/COLOR][/B]) 1991 ZR-1 #473 [COLOR=red]RED/[/COLOR][COLOR=black]BLACK [/COLOR]37k miles ([B][COLOR=red]SOLD[/COLOR][/B])[/SIZE][/FONT][/I]