FS: Low km INA throwout Bearing, Fidanza Aluminum flywheel, OEM pressure plate

[5ABI VT]

EDIT** everything is out and for sale.


Will be up for sale shortly just wanted to start a thread if thats ok. Had the setup in for about 2k miles. Believed the clutch to be slipping but didnt even drive it since to figure it out since I planned a twin disc replacement anyways. Car still runs and drives and shifts fine. Will make a video today or tomorrow if I can find time to fire it up and idle with clutch in and out to show how quiet and whine free the setup is. Might be keeping the slave cylinder for my 93 Lt1 car. Bearign was brand new when installed in my car. I purchased an old stock clutch setup and kept the bearing and sold the oem pressure plate that was new etc. have pics and documentation to show the purchase etc from ebay.

Fidanza $225
oem pp was refurbished by Jim Jandik $100


Plus shipping.

[Vette73]

Is fidanza flywheel still available?

Sent from my LG-TP260 using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[5ABI VT]

Is fidanza flywheel still available?

Sent from my LG-TP260 using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

It is still available. I hope to have it out very soon I haven't had any time at all to work on the car but it shouldn't take more than a few hours when I get started. I should the prices were plus shipping .. will add it to the op.

[5ABI VT]

Wanted to bump this instead of making a new thread. Everything is for sale and ready to go.

Some pics right before install and after removal. The flywheel surface was covered in fluid I believe from the Slave. The disc that was removed had literally 0 wear as I only had about 1500-2k km on the setup. Pulled it all due to a little slippage due to oil contamination and decided to just go twin disc and hydraulic t.o bearing conversion from Jerry/Ram.

Whole setup before install
https://s19.postimg.cc/dpksqhtcz/A3_D5_FB34-_AFA3-41_F9-_A0_F3-203_ED6212023.jpg (https://postimg.cc/image/jdr3hdxpb/)
LT5 pressure plate
https://s19.postimg.cc/uq3oz5qyr/7_E214_B3_B-24_A5-497_B-_B4_FE-4_F666481_A158.jpg (https://postimg.cc/image/57bcm57en/)
Fidanza/ spec light flywheel
https://s19.postimg.cc/9gg2ob2yb/70_C057_C1-3366-4811-9_A79-3_A470_EE64_AEC.jpg (https://postimg.cc/image/3s9rxeylr/)
Flywheel after removal
https://s19.postimg.cc/uq3oz6ltv/9463_C757-029_D-4047-9946-_CF5059799_F4_B.jpg (https://postimg.cc/image/qtqd370u7/)

[scottskill]

What's the condition of the disk?

Sent from my SM-G955U using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[5ABI VT]

What's the condition of the disk?

Sent from my SM-G955U using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

Here’s a pic of the disk. It’s pretty much new there was signs of some oil/brake fluid which was causing the slight slippage. Not sure if it can be brake cleaned and used but happy to throw it in with either the Pp, flywheel or both. It’s a dual friction organic on one side and metallic on the other and sprung center.
https://s19.postimg.cc/jwnavraxf/83_F3_B269-_EE76-4_C48-_B795-55108814426_D.jpg (https://postimg.cc/image/3ln6zfyfj/)

[scottskill]

Sir, Who manufactured the clutch disk and is there a part #

Sent from my SM-G955U using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[5ABI VT]

Sir, Who manufactured the clutch disk and is there a part #

Sent from my SM-G955U using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

The disc is not an oem disk. I believe it’s a Spec brand.

[scottskill]

Sir, still available?

Sent from my SM-G955U using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[5ABI VT]

Sir, still available?

Sent from my SM-G955U using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

Yes still available ! :)

[scottskill]

Can a stock throw out bearing be used as well as stock fly wheel to crank bolts?

Sent from my SM-G955U using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[5ABI VT]

I purchased the arp flywheel bolts from Jerry for the install I can include them with the flywheel I believe they are much better/stronger than oem bolts. And yes oem throwout bearing works as well with this setup.

[A26B]

OE Dual Mass Flywheel bolts cannot be used with any aftermarket flywheels. They are much too long.

[5ABI VT]

OE Dual Mass Flywheel bolts cannot be used with any aftermarket flywheels. They are much too long.

Thanks for clarifying ! Jerry does sell the bolts for the flywheel. Jerry are the arp flywheel bolts reuseable ?

[scottskill]

What's your asking price for your clutch and associated hardware?

Sent from my SM-G955U using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[Flyman 27]

Have you sold the INA throw out bearing?
How much do you want for it?

[5ABI VT]

Have you sold the INA throw out bearing?
How much do you want for it?

The Ina bearing im keeping. I have my 93 with its built LT4 stroker I need to put back together with a blue tag zf6 so ill be using it for that.

[A26B]

Thanks for clarifying ! Jerry does sell the bolts for the flywheel. Jerry are the arp flywheel bolts reuseable ?

Yes

[Blackbelt]

Will you take $300 shipped for the whole set up shipped to 92584?

[5ABI VT]

Will you take $300 shipped for the whole set up shipped to 92584?

pm inc !