![]() |
#1 |
![]() Join Date: Feb 2005
Location: Springfield, PA
Posts: 372
|
![]()
I need to replace the rear wheel bearings. I know MOOG, Timken and SKF are good names. The below is what Rock Auto lists. Which bearing would you install?
RAYBESTOS Part # 713020 Professional Grade Rear ...$91.79 TIMKEN Part # 513020 Ball Bearing Rear $99.79 MOOG/NATIONAL Part # 513013 {Click Info Link for Alternate/OEM Part Numbers513020, 7466907, 7466920, 7466942, 7466952, 7470005, 7470536} Rear $100.79 MOOG/NATIONAL Part # 513020 Rear Hub Assembly $105.79 SKF Part # BR930024 {#7466924, 7466945} Wheel Hub Assembly Rear $142.79 ACDELCO Part # 2045 {#07470501, 7470501} GM Original Equipment Rear (Only 1 Remaining) $282.79
__________________
John Porter '93 Ruby Coupe ZF6 - Muffler eliminators, Blink Blink kit and Polished ZR1 Wheels * PA Plate: OBSSSN '06 LeMans Blue C6 Coupe - Corsa exhaust * PA Plate: OBSSSV ZR1 Net Registry Founding Member #153 40th Anniversary Registry Member NCM Family Membership #8116 Corvette Forum NE Events Coordinator Delco Cruisers Board of Directors SAVE THE WAVE! Last edited by Rex Ruby; 03-14-2015 at 01:51 PM. |
![]() |
![]() |
![]() |
#2 |
![]() Join Date: Dec 2003
Location: Arcadia,OK
Posts: 3,384
|
![]()
Timkin
__________________
Jerry Downey JERRYS LT5 GASKETS & PARTS http://www.jerrysgaskets.com 1994 ZR-1, Black/Black, Lingenfelter Aerobody, 416cu in, 3.91 gears, coil-over susp, Brembo brakes, etc. 2016 Black-Red, 3LT-Z51 Auto 8-speed. |
![]() |
![]() |
![]() |
#3 |
![]() Join Date: Feb 2005
Location: Springfield, PA
Posts: 372
|
![]()
__________________
John Porter '93 Ruby Coupe ZF6 - Muffler eliminators, Blink Blink kit and Polished ZR1 Wheels * PA Plate: OBSSSN '06 LeMans Blue C6 Coupe - Corsa exhaust * PA Plate: OBSSSV ZR1 Net Registry Founding Member #153 40th Anniversary Registry Member NCM Family Membership #8116 Corvette Forum NE Events Coordinator Delco Cruisers Board of Directors SAVE THE WAVE! |
![]() |
![]() |
![]() |
#4 |
![]() Join Date: Feb 2011
Location: San Marcos CA
Posts: 1,802
|
![]()
The SKF (if made in South Korea) are highly regarded for the C4 application. I bought some for the fronts (F-Body ones because they were cheaper).
|
![]() |
![]() |
![]() |
#5 |
![]() Join Date: Apr 2007
Location: Northern VA
Posts: 2,654
|
![]()
Both Timken and SKF are fine.
I'm running SKF bearing hubs on the rear broached out to 31 splines for Mark Williams spindles. Here is the broached out SKF next to a stock ACDelco hub: ![]()
__________________
Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake |
![]() |
![]() |
![]() |
#6 |
Join Date: May 2007
Location: Chicagoland, IL
Posts: 9,697
|
![]()
I try to use Moog suspension bits and SKF bearings for the most part.
__________________
[SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX |
![]() |
![]() |
![]() |
#7 |
Join Date: Jun 2009
Location: I live at Devens, one run at a time
Posts: 455
|
![]()
For street use I think any major brand will be fine, although it appears Moog has a longer warranty (3 years).
For my application (autocross racing on big slicks), I've burned up all I've tried but am looking forward to trying Moog this year. The Moog part appears to have a different seal design and that looks to be my root cause of failure. It does seem most of the hubs are coming from one factory in China - I've had a litany of switched bits like a National flange on an SKF or other ident not matching its' box brand. At least they're easy to change, well at least until you machine things or use long studs. Cheers, - Jeff
__________________
[I]91 ZR-1 #1840, autocrossing in SCCA BSP. FIC S/S's DRM chip/Watson/Borla/lid/LW batt&headlights, springs, shocks, pads & lines, quick rack & Turn One, camber brace, 32/22mm sways, A/C halfway deleted 17x11 & 12 CCW's, 315 & 335 Hoosier A6s [/I] |
![]() |
![]() |
![]() |
|
|