![]() |
#1 |
![]() Join Date: Dec 2005
Posts: 692
|
![]()
I'm just curious......Who's planning on going to the PNW Gathering in Las Vegas?
|
![]() |
![]() |
![]() |
#2 |
Guest
Posts: n/a
|
![]()
I'll be there. If I'm bringing a car I may haul it down. But I may be flying.
|
![]() |
![]() |
#3 | |
![]() ![]() Join Date: Aug 2005
Location: Northridge, CA
Posts: 1,457
|
![]() Quote:
![]() I'll be there........ |
|
![]() |
![]() |
![]() |
#4 | |
![]() ![]() ![]() Join Date: May 2007
Location: Peoria, AZ
Posts: 9,153
|
![]() Quote:
Hmmm ![]() ![]() |
|
![]() |
![]() |
![]() |
#5 |
Join Date: Aug 2005
Location: San Fernando Valley, CA.
Posts: 896
|
![]()
I should be there this year.
__________________
1990 ZR1, 142,000 miles-Black on black 4.09's Haibeck chip, 3"exh, K&N, meth inj. |
![]() |
![]() |
![]() |
#6 |
Join Date: Aug 2005
Location: Scottsdale, AZ
Posts: 2,450
|
![]()
I will be there again
Goldcylon, you better be going |
![]() |
![]() |
![]() |
#7 |
![]() ![]() ![]() Join Date: May 2007
Location: Peoria, AZ
Posts: 9,153
|
![]()
Will need to check in with Household 6!!!! BTW
PS P&P and PC job is done. Awaiting two parts before the big reveal. Taking her to the Dyno tomorrow. Last edited by GOLDCYLON; 08-14-2007 at 11:01 PM. |
![]() |
![]() |
![]() |
#8 | |
![]() ![]() Join Date: Aug 2005
Location: Northridge, CA
Posts: 1,457
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#9 | |
Join Date: Aug 2005
Location: San Fernando Valley, CA.
Posts: 896
|
![]() Quote:
Oh well, someone has to be the slow guy ![]()
__________________
1990 ZR1, 142,000 miles-Black on black 4.09's Haibeck chip, 3"exh, K&N, meth inj. |
|
![]() |
![]() |
![]() |
#10 | |
![]() ![]() ![]() Join Date: May 2007
Location: Peoria, AZ
Posts: 9,153
|
![]() Quote:
Heres a talley of what was done!!! Porting and polishing of entire top end to include plenum, air horn and injector housings. Entire top end from Throttle shield cover to MAP sensor bracket was powercoated in Silver Metallic Paint with red and black lettering. All work done by Jeffvette. Diassembly and assembly was completed by Bill B the ZF.Doc and his trusty helper. I chose to replace the following during the tear down. Removed Original Injectors and replaced with RC SL4-205s (all the originals were rusted BTW) New Plugs, Iridium of course New Wires, Delco of course 4 New Delco Coil Packs 1 New Starter 2 New PCV Valves and PCV tubing 1 New MAP sensor but dammit I bought the wrong part (lol) Carter provided Machined LT-5 Coolant Pipes, LT-5 TPI Cover and a ZR-1 Billet Oil Filter cover Zethco hooked me up with Macallister for all the stainless hardware Pics to follow, If I can get a kitchen pass after pulling off all these mods with Household 6 I will be in LV for at least a few days. ![]() All these folks made this happen and the Permagrin continues to get wider. It all about the car and the people folks!! Goldcylon Last edited by GOLDCYLON; 08-15-2007 at 08:57 AM. |
|
![]() |
![]() |
![]() |
|
|