Lower Seat Position - ZR-1 Net Registry Forums

JThomas · 03-31-2018

Does anyone know of a remedy to create a lower seat position in the C4? I have a '91 Corvette ZR-1 that I recently had the seats re-upholstered. The new foam/padding has caused me to lose what little headroom I had in the car.

I am looking for a solution to lower the seats in my car without compromising the padding or comfort of the seats.

Is there a way to remove the power seat mechanisms and possibly have the seats permanently mounted in the car? At 6'6" they need to be all the way back and as low as possible. I'm not concerned with resale of the car at this point or anyone else's comfort/ability to drive the car.

I have already removed the support straps under the cushions, but that is not enough. I'm looking for other solutions.

Thanks,

Joe

gbrtng · 03-31-2018

Gurney bubble?

JThomas · 03-31-2018

Quote:

Originally Posted by gbrtng

Gurney bubble?

Thanks but that doesn't fit the theme of this project.

secondchance · 03-31-2018

Joe,

I think what can be done is to fabricate 2 (left and right) pieces, channel shaped, brackets that can be bolted to the floor in same location as the track. Then, seats can be bolted to the top of the track. Track total thickness when in the lowest seat position, based on my memory, is about 3-4 inches. Channel shaped bracket can 1-2 inches.
I'll hand sketch what can be done and email to you. You can talk to Dempsey - evolution motor sport, and have him fabricate the piece, paint and ship to you.
What is your Z model year?

https://www.google.com/search?q=c4+s...YUNUeASyWwsqM:

JThomas · 03-31-2018

Quote:

Originally Posted by secondchance

Joe,

I think what can be done is to fabricate 2 (left and right) pieces, channel shaped, brackets that can be bolted to the floor in same location as the track. Then, seats can be bolted to the top of the track. Track total thickness when in the lowest seat position, based on my memory, is about 3-4 inches. Channel shaped bracket can 1-2 inches.
I'll hand sketch what can be done and email to you. You can talk to Dempsey - evolution motor sport, and have him fabricate the piece, paint and ship to you.
What is your Z model year?

https://www.google.com/search?q=c4+s...YUNUeASyWwsqM:

My car is a 1991. I like your solution, but I thought for sure someone else had already been down this road.

-=Jeff=- · 03-31-2018

Locobob had taken a manual seat track and made it lower as well, that could work for you

secondchance · 03-31-2018

Quote:

Originally Posted by -=Jeff=-

Locobob had taken a manual seat track and made it lower as well, that could work for you

Modify these?
That could work.

https://www.ebay.com/p/84-96-Corvett....c100005.m1851

efnfast · 03-31-2018

Joe, I assume you run with the Lexan roof. Its a little thinner than the solid top.

JThomas · 03-31-2018

Quote:

Originally Posted by efnfast

Joe, I assume you run with the Lexan roof. Its a little thinner than the solid top.

Absolutely! It gives me just a little more headroom.

XfireZ51 · 03-31-2018

Quote:

Originally Posted by JThomas

Absolutely! It gives me just a little more headroom.

That was going to be my suggestion.
BTW Joe, speaking of extra room, I’m trying to get a group buy together for the Apsis D shape wheel. I know that would afford you some extra knee room and easier egress. Interested?
Full disclosure, I don’t know that Apsis would be interested but worth a try.

03-31-2018	#1
JThomas Join Date: May 2008 Location: Okemos, MI. Posts: 1,189	Lower Seat Position Does anyone know of a remedy to create a lower seat position in the C4? I have a '91 Corvette ZR-1 that I recently had the seats re-upholstered. The new foam/padding has caused me to lose what little headroom I had in the car. I am looking for a solution to lower the seats in my car without compromising the padding or comfort of the seats. Is there a way to remove the power seat mechanisms and possibly have the seats permanently mounted in the car? At 6'6" they need to be all the way back and as low as possible. I'm not concerned with resale of the car at this point or anyone else's comfort/ability to drive the car. I have already removed the support straps under the cushions, but that is not enough. I'm looking for other solutions. Thanks, Joe __________________ Joe Thomas Corvette Club of Michigan NCRS-Michigan Chapter Member NCM Master Ambassador NCM Lifetime Member Former NCM Board Member 1991 ZR-1 Melon Copper Metallic/Black 1992 ZR-1 Bright Red/Black (Sold) 1995 ZR-1 Bright Aqua/Gray (Sold) 2012 ZR1 Super Sonic Blue / Dark Titanium

03-31-2018	#2
gbrtng Join Date: Feb 2006 Location: San Antonio area Posts: 1,179	Re: Lower Seat Position Gurney bubble? __________________ “Buy the best example of what you want, and pay whatever it takes. That way, you cry only once.” ~ Bruce Meyer

03-31-2018	#4
secondchance Join Date: Aug 2006 Location: McLean, VA Posts: 3,712	Re: Lower Seat Position Joe, I think what can be done is to fabricate 2 (left and right) pieces, channel shaped, brackets that can be bolted to the floor in same location as the track. Then, seats can be bolted to the top of the track. Track total thickness when in the lowest seat position, based on my memory, is about 3-4 inches. Channel shaped bracket can 1-2 inches. I'll hand sketch what can be done and email to you. You can talk to Dempsey - evolution motor sport, and have him fabricate the piece, paint and ship to you. What is your Z model year? https://www.google.com/search?q=c4+s...YUNUeASyWwsqM:

03-31-2018	#6
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,154	Re: Lower Seat Position Locobob had taken a manual seat track and made it lower as well, that could work for you __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978

03-31-2018	#8
efnfast Join Date: Nov 2011 Location: Dunbarton NH Posts: 7,375	Re: Lower Seat Position Joe, I assume you run with the Lexan roof. Its a little thinner than the solid top.