![]() |
#1 |
Join Date: May 2007
Location: Chicagoland, IL
Posts: 9,697
|
![]()
Ok, last year I installed a Fluidyne rad to keep temps down particularly when in traffic w A/C on. Worked great have however, with ambient temps below 60, it was difficult to maintain operating temps on motor. At cruise, coolant temps would drop into the 150-160 range. Which is not desired if you want Closed Loop operation w Learn Control. So I finally bought a stock therm from Jerry's and had it installed. turns out the thermo coming OUT of the motor had 5 holes drilled in it. The stock thermo was installed w 0 holes.
The result is that coolant temps increase now unless motor is turning above 12-1300 rpm. That includes at highway cruise. So I know I don't need 5 holes in thermo, but I'd like to avoid doing this again. How many holes should I put in stock thermo so that fans can maintain steady operating temps? I should add that I have under drive pulleys and temps creep up they don't shoot up.
__________________
[SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX Last edited by XfireZ51; 10-21-2016 at 05:06 PM. |
![]() |
![]() |
![]() |
#2 | |
![]() Join Date: Aug 2006
Location: McLean, VA
Posts: 3,713
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#3 |
Join Date: May 2007
Location: Chicagoland, IL
Posts: 9,697
|
![]()
Do u know what temps ur fans come on at?
__________________
[SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX |
![]() |
![]() |
![]() |
#4 |
![]() ![]() ![]() Join Date: May 2007
Location: Peoria, AZ
Posts: 9,153
|
![]()
I have the Dewitt's radiator with a Ron woods 160 thermostat and one drilled hole. I have the fans on early mod and the Dewitt's spal fans. In wintertime the car randomly exceeds 1/2 band on the gauge. I would say no more than 2 Dom as 5 is almost a bypass
__________________
GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director ![]() 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V Last edited by GOLDCYLON; 10-24-2016 at 10:00 AM. |
![]() |
![]() |
![]() |
#5 |
![]() Join Date: Aug 2006
Location: McLean, VA
Posts: 3,713
|
![]() |
![]() |
![]() |
![]() |
#6 |
Join Date: May 2007
Location: Chicagoland, IL
Posts: 9,697
|
![]()
Ok, one other question. What diameter for the holes?
__________________
[SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX |
![]() |
![]() |
![]() |
#7 |
![]() Join Date: Aug 2006
Location: McLean, VA
Posts: 3,713
|
![]() |
![]() |
![]() |
![]() |
#8 |
![]() ![]() Join Date: Aug 2009
Location: South Dakota/California
Posts: 3,794
|
![]()
Ok guys.......just a little experience with thermostats (180 deg), Dewitts, Fluidyne, Ron Davis ALuminum Radiators, Fans, and Water Pumps for ZR-1s
1. Fans turn on at 205 deg F and OFF at 200 deg F (Haibeck Chip) 2. I use 180 deg Thermostats. 3. Ron Davis, Dewitt, and Fluidyne multi core Aluminum Radiators. My experience in all ambient temperatures. A. In sixth gear running 65 mph (less than 2,000 rpm) the Coolant always gets a bit over 200 deg F. On Hot days the coolant will get a bit over 213 deg F. The key is the Water Pump is not pushing enough flow through the fully open thermostat to cool the engine to a Temperature where the Thermostat takes over (180 deg F). B. If I shift to 5th gear at 65 mph (more than 2,000 rpm) the coolant temperature drops to Thermostat control (180 deg F) on cool days and drops to near 200 deg F on Hot days. The Summary is simple..... The Thermostat is fully open at all coolant temperatures over 180 deg F (no need to use cooler thermostat unless you want to run at temperatures below 180 deg F). The Water Pump does not provide enough flow to cool the engine at rpms less than 2,000 rpm. This is not an issue at ambient environmental temperatures on cool days. This is a problem on HOT days. The Aluminum Multi Core Radiators DO provide better Heat Dissipation and offer cooler Coolant at ALL Temperatures for which the 180 deg F Thermostat Controls the Flow (above 180 deg F Coolant temperatures the Thermostat is fully open). The Cooling effects then being dependent on Water Pump Flow Rate and Air Flow Rate through the Radiator. Having the Fans come on at 205 deg F DOES provide for COOLER Coolant in the radiator once sufficient coolant flow rate is provided above 2,000 rpm. Using Aluminum Multi Core Radiators ALSO provides for COOLER Coolant Temperatures in conjunction with the Air Flow provided by Fans and Vehicle Speed. The Heat Removal Rate from the Radiator is greater as the Air Flow Increases and as the Aluminum exposed to that Air Movement increases. It DOES make a difference if you are moving at speed in conjunction with Fans PULLING Air Flow as the additional Air Pressure Up Front does add to the TOTAL AIR FLOW through the Radiator at any ambient environmental temperatures. Using 180 deg Thermostats insures that the engine will not run cooler than that temperature since the Thermostat is in control and controls the Coolant flow rate through the engine at all Coolant Temperatures less than 180 deg F. Thermostats, Fans, Water Pump, and Radiators
__________________
Left Clickable links ![]() -Solutions- LT5 Modifications/Rebuild Tricks Low Mileage ZR-1 Restoration 1990 Corvette (L98) Modifications LT5 Eliminated Systems LT5 Added Systems LT5/ZR-1 Fluids 1995 LT5 SPECIFIC TOP END REBUILD TRICKS Last edited by Dynomite; 10-21-2016 at 09:28 PM. |
![]() |
![]() |
![]() |
#9 | |
![]() ![]() Join Date: Nov 2007
Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri
Posts: 6,493
|
![]() Quote:
![]()
__________________
Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry |
|
![]() |
![]() |
![]() |
#10 |
![]() Join Date: Jan 2015
Location: Decatur, AL
Posts: 93
|
![]()
Dynamite is correct. All those extra holes in the thermo could delay opening a little. Prob wouldn't notice. A good thermo has a bleed hole. All you need is one hole and install it at the top to bleed any trapped air. 180 is the way to go. And it will help some to have a fan come on at 185-190 but coolant flow is more important. With ac the fans should be running anyway, but idle in hotter temps is still going to stress the system. Too cool a thermo will result in the engine staying in "choke mode" in colder weather.
Sent from my iPhone using ZR-1 Net Registry
__________________
1990 ZR1, 1987 Mustang GT (since new), 1973 DeTomaso Pantera, 1987 928S4 Passed on: 1984 930S (gray market), 1988 Mustang Coupe Trooper car(drag) |
![]() |
![]() |
![]() |
|
|