![]() |
#1 |
![]() Join Date: Jun 2006
Location: Sparks, NV
Posts: 2,852
|
![]()
To date I’ve done more plenum pulls than I can count and other than a blown INJ1 fuse or a finicky coolant fill I’ve never run into any issues with codes when finished. Recently in doing one for a friend we ended up with a code 42 when it was all buttoned up. Very irritating. After running some diagnostics, specifically the FSM diagnostic tree for code 42, we determined that the most likely issue was a bent pin at the main DIS module connector. This means pulling the plenum again. Which also means draining and later refilling coolant. Some searches on the forum revealed that this is not an uncommon issue because of the awkward access to the main DIS connector for reassembly. It doesn’t take much for even a slight misalignment to cause a bent connector pin. That’s what we found, a bent pin.
It occurred to me that if I added one step to the reassembly process I could assure no code 42 and the associated work of a second plenum pull and coolant drain/refill. Its simple. (Note, you will need a Tech1 or code reader of some type.) When you get to the point where the plenum is on (not bolted down) and all the DIS connectors are in place, stop. Now connect all the other electronic connectors that came off in the process, if only temporarily. The MAT sensor, Idle Air Motor, the Throttle Position Sensor and the MAP Sensor. If you disconnected your battery, reconnect it. At this point simply turn the ignition on. (Don’t turn the engine over!) Your code reader will now tell you if there are any codes. A code 42 will instantaneously come on if it’s there. If there is no code 42 your good to go. If you do find a code 42 clear it, cycle the ignition off and back on (don’t turn the engine over). If the code comes back you likely have a bent DIS connector pin. You can now more easily go back and check the connector pins. You just saved yourself a full second plenum pull. H ![]()
__________________
90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold. |
![]() |
![]() |
![]() |
#2 |
![]() ![]() Join Date: Aug 2009
Location: South Dakota/California
Posts: 3,794
|
![]()
Block TB Coolant at Injector Housing if you want to make it super easy to remove the Plenum
![]() See .........1995 LT5 SPECIFIC TOP END REBUILD TRICKS in signature.
__________________
Left Clickable links ![]() -Solutions- LT5 Modifications/Rebuild Tricks Low Mileage ZR-1 Restoration 1990 Corvette (L98) Modifications LT5 Eliminated Systems LT5 Added Systems LT5/ZR-1 Fluids 1995 LT5 SPECIFIC TOP END REBUILD TRICKS Last edited by Dynomite; 12-20-2019 at 07:05 PM. |
![]() |
![]() |
![]() |
#3 | |
![]() Join Date: Jun 2006
Location: Sparks, NV
Posts: 2,852
|
![]() Quote:
H ![]()
__________________
90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold. |
|
![]() |
![]() |
![]() |
#4 |
![]() ![]() Join Date: Aug 2009
Location: South Dakota/California
Posts: 3,794
|
![]()
I removed the two MAP Sensor Bolts (those two bolts are now Allen head) one time making it very easy to disconnect MAP Vacuum and the MAP electrical connector (then removing the MAP bracket and sensor completely). This then made it considerably easier to disconnect/connect the DIS connector with 1/4 inch socket and a 1/4 inch socket wrench with 4 inch extension.
I then connected the MAP electrical plug to the MAP sensor before connecting the MAP bracket with MAP sensor to the Plenum after Plenum is installed which was very easy. I have never bent a connector pin in the DIS (DIM) but that definitely can happen and worthy of your checking procedure ![]() This is a 95' Plenum...... ![]()
__________________
Left Clickable links ![]() -Solutions- LT5 Modifications/Rebuild Tricks Low Mileage ZR-1 Restoration 1990 Corvette (L98) Modifications LT5 Eliminated Systems LT5 Added Systems LT5/ZR-1 Fluids 1995 LT5 SPECIFIC TOP END REBUILD TRICKS Last edited by Dynomite; 12-20-2019 at 08:48 PM. |
![]() |
![]() |
![]() |
#5 |
Join Date: May 2013
Location: Chicago
Posts: 978
|
![]()
Mine had a code 16 with a bent pin. See post #25
Got my car at a pretty good deal due to this a few miscellaneous issues. http://www.zr1.net/forum/showthread.php?t=29346&page=3
__________________
1993 ZR-1 #211 Yellow On Beige Beast #2 1992 ZR-1 #427 Black On Black *Sold* 1985 L98 Blue On Blue *Sold* |
![]() |
![]() |
![]() |
#6 | |
![]() Join Date: Jun 2006
Location: Sparks, NV
Posts: 2,852
|
![]() Quote:
H ![]()
__________________
90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold. |
|
![]() |
![]() |
![]() |
#7 |
![]() Join Date: Aug 2004
Location: Spring Grove ,Pa.
Posts: 256
|
![]()
It's been a while since I did a plenum pull. I have a slight vacuum leak that could be the plenum gaskets. Hoping it's not the injector housing gaskets. I guess I can't getaway with just slipping in new plenum gaskets or can I. Just drain a bit of coolant and remove the bolts to the plenum. Raise the plenum a bit and prop it up just enough to install the new gaskets on the top of the injector housing and then bolt the plenum back up.
Marc ported the heads ,injector housing, and plenum. There are no secondary's anymore, or secondary actuators all that stuff is history. Anybody have a view of a LT5 with the secondary delete? With the plenum pulled that is.
__________________
91 Turquoise Metallic Haibeck 525 #0134 |
![]() |
![]() |
![]() |
#8 |
![]() Join Date: Jun 2006
Location: Sparks, NV
Posts: 2,852
|
![]()
__________________
90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold. |
![]() |
![]() |
![]() |
#9 | |
![]() ![]() Join Date: Aug 2009
Location: South Dakota/California
Posts: 3,794
|
![]() Quote:
![]() The most unique feature of the LT5 is the Full Power Key........... ....But.......I admit on one ZR1 I have also eliminated Secondaries ![]() Looks like you blocked TB Coolant....... ......but your Plenum Gasket is backward ![]() ![]()
__________________
Left Clickable links ![]() -Solutions- LT5 Modifications/Rebuild Tricks Low Mileage ZR-1 Restoration 1990 Corvette (L98) Modifications LT5 Eliminated Systems LT5 Added Systems LT5/ZR-1 Fluids 1995 LT5 SPECIFIC TOP END REBUILD TRICKS Last edited by Dynomite; 12-22-2019 at 01:04 PM. |
|
![]() |
![]() |
![]() |
#10 |
![]() Join Date: Nov 2016
Location: Southlake, TX
Posts: 588
|
![]()
What are Y'all doing to hold the gasket in place when putting the plenum back on?
I had a buddy help me a while back who is a former pro-motor cycle racer. He used hair-spray. I never heard of such a thing put it worked!
__________________
Bill Schroeder Texas Proud! 1991 Corvette ZR1 #1388 2015 Challenger Scat Pack Shaker ![]() |
![]() |
![]() |
![]() |
|
|