![]() |
#81 | |
![]() Join Date: Jun 2006
Location: Sparks, NV
Posts: 2,852
|
![]() Quote:
H ![]()
__________________
90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold. |
|
![]() |
![]() |
![]() |
#82 |
![]() Join Date: Nov 2016
Location: Norway
Posts: 397
|
![]()
The upper one, yes. Not the one surrounding the shifter mechanism.
__________________
- '90 ZR-1 |
![]() |
![]() |
![]() |
#83 |
![]() Join Date: May 2008
Location: Okemos, MI.
Posts: 1,189
|
![]()
Here is a picture of my seats installed in the car. They have a matte or duller finish, but it fits my theme.
__________________
Joe Thomas Corvette Club of Michigan NCRS-Michigan Chapter Member NCM Master Ambassador NCM Lifetime Member Former NCM Board Member 1991 ZR-1 Melon Copper Metallic/Black 1992 ZR-1 Bright Red/Black (Sold) 1995 ZR-1 Bright Aqua/Gray (Sold) 2012 ZR1 Super Sonic Blue / Dark Titanium |
![]() |
![]() |
![]() |
#84 |
![]() Join Date: Nov 2016
Location: Norway
Posts: 397
|
![]()
The seats look mint!
Mine also has the matte look, but of unknown reasons the "corvette" stitching was black. The foam also didn't really fit perfectly, as the metal inside was not positioned precisely enough.
__________________
- '90 ZR-1 |
![]() |
![]() |
![]() |
#85 |
![]() Join Date: Nov 2016
Location: Norway
Posts: 397
|
![]()
Car's finally back on the road, and all clutch related noises have disappeared.
Not a complete success though, as I managed to tear the lower boot while installing. Guess NOS rubber also means brittle rubber. To add salt to injury, the rubber-like trim on the drivers side of the console is also starting to let go of its plastic frame, letting in all kinds of transmission noises. Is it possible to aquire this part? The throttle body repair seemingly did nothing. Idle is still 750 RPM with 0 IAC counts. More vacuum leak searching to come. The Corsa exhaust I bought here on the forum has removed the drone, but it's still incredibly loud, even at very low loads. A bit annoyed with myself for not checking if the cats had been gutted while the exhaust was removed.
__________________
- '90 ZR-1 Last edited by S.hafsmo; 07-12-2018 at 04:37 AM. |
![]() |
![]() |
![]() |
#86 | |
![]() Join Date: Jun 2006
Location: Sparks, NV
Posts: 2,852
|
![]() Quote:
http://www.zr1.net/forum/showthread....hlight=Min+air H ![]()
__________________
90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold. |
|
![]() |
![]() |
![]() |
#87 |
![]() Join Date: Nov 2016
Location: Norway
Posts: 397
|
![]()
I have not. Will do this before doing any more digging. Thanks!
__________________
- '90 ZR-1 |
![]() |
![]() |
![]() |
#88 |
![]() Join Date: Nov 2016
Location: Norway
Posts: 397
|
![]()
Did the minimum air adjustment today, but unfortunately to no avail. The throttle blades came back from Haibeck completely closed, and unscrewing the throttle adjustment screw any further did not change the idle. Could see the screw lifting from the throttle.
Could not find any external leaks using motor starter spray around manifold and Connections, nor could I reduce the throttle by disconnecting and blocking manifold vacuum outlets. The only thing affecting the idle, was removing the pipe to the crank vent, and blocking it. This reduced the idle to a lumpy 500 RPM. Is it correct that such amounts of air should be sucked through the crank? The breather hoses are new, and one (of the two) of the internal valves has been replaced. Could not find the second one, but seem to remember having tested it for proper function/tightness. Anyway, to get the car nice and warm, I took it out for a spin on the Island where the vessel I currently work on is docked. ![]() Wanted to take a pic of the car below the Arctic circle marker, but too many people around, and I dont like being seen taking photos of my car. ![]() And yes, my camera is still aweful.
__________________
- '90 ZR-1 |
![]() |
![]() |
![]() |
#89 |
Join Date: May 2007
Location: Chicagoland, IL
Posts: 9,697
|
![]()
The crank vent? Do u mean the PCV tube?
__________________
[SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX |
![]() |
![]() |
![]() |
#90 |
![]() Join Date: Nov 2016
Location: Norway
Posts: 397
|
![]()
Yes, doesn't it draw through the injector housings? Positive Crank Vent?
__________________
- '90 ZR-1 |
![]() |
![]() |
![]() |
|
|