WANTED: Cam position sensor for LT5 - Page 5 - ZR-1 Net Registry Forums

Z51JEFF · 12-21-2017

Quote:

Originally Posted by A1990

Picture from Jeff:

Another picture

Sent from my iPhone using ZR-1 Net Registry

Thanks Dennis.

Jagdpanzer · 12-23-2017

The alternative cam position sensor arrived today. Had to make some modification to it so it would fit in cylinder head in place of the OEM stock sensor. Here it is beneath the OEM sensor:

Fit was identical to the OEM sensor.

Same 1mm camshaft reluctor wheel clearance as with the OEM sensor.

Did some bench testing by installing in a head and turning the cam by hand and it generated the same signal output as the OEM sensor.

Facing slot

Facing wheel

Looking very promising so far. Next up full scale testing in the car.

A26B · 12-23-2017

Sweet! Another critical LT5 part well on the way to being solved!
THANK YOU PHIL!

Young1 · 12-23-2017

I am impressed and thankful for all the expertise and dedication for the sake of everyone that enjoys these cars. This is neat to see it come together. I hope you have good weather for testing.

Sent from my iPhone using ZR-1 Net Registry

tnova · 12-23-2017

Phil, Once again to the rescue of the LT5. Highly interested in the end result so I may replace the sensor in my LT5 while it's out of the car and prior to installing the cam covers.
Tony - Tnova

Jagdpanzer · 12-23-2017

Installed the alternative camshaft position sensor on my 94 Z this afternoon and it performed perfectly during garage running tests. Even disconnected the signal wire which immediately triggered code 31 cam sensor failure. Reconnected and all was fine again. Rainy weather here prevented a more thorough road test however, from what I've seen thus far I'm confident it will perform just as well as the OEM sensor.

Young1 · 12-23-2017

Great news for my ailing Z

Sent from my iPhone using ZR-1 Net Registry

Jagdpanzer · 12-23-2017

Quote:

Originally Posted by Z51JEFF

Phil,if you send me what you have I’ll use my terminals-connectors and finish the plug. I can then confirm it’s a perfect plug and go with my car.

Jeff,
Thanks for the offer. In the meantime Dave got me straightened out on the Metri-pack connector components I needed which are now on order and should arrive by Wednesday.

Sent from my iPhone using ZR-1 Net Registry

secondchance · 12-24-2017

Fantastic job, Phil!
So, which model is this sensor originally listed for? Another GM model?

Jagdpanzer · 12-24-2017

It’s an generic aftermarket piece I found with a form close enough for replacing the OEM sensor.
Modifications:
• Machined spacer ring for adapting the sensor to the cylinder head mounting bore location.
• Correct size O-ring
• Machining O-ring groove
• Fabing up cable plug end
• Installing split wiring conduit

12-23-2017	#42
Jagdpanzer Join Date: Apr 2007 Location: Northern VA Posts: 2,658	Re: WANTED: Cam position sensor for LT5 The alternative cam position sensor arrived today. Had to make some modification to it so it would fit in cylinder head in place of the OEM stock sensor. Here it is beneath the OEM sensor: Fit was identical to the OEM sensor. Same 1mm camshaft reluctor wheel clearance as with the OEM sensor. Did some bench testing by installing in a head and turning the cam by hand and it generated the same signal output as the OEM sensor. Facing slot Facing wheel Looking very promising so far. Next up full scale testing in the car. __________________ Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake

12-23-2017	#43
A26B Join Date: Dec 2003 Location: Arcadia,OK Posts: 3,393	Re: WANTED: Cam position sensor for LT5 Sweet! Another critical LT5 part well on the way to being solved! THANK YOU PHIL! __________________ Jerry Downey JERRYS LT5 GASKETS & PARTS http://www.jerrysgaskets.com 1994 *ZR-1*, Black/Black, Lingenfelter Aerobody, 416cu in, 3.91 gears, coil-over susp, Brembo brakes, etc. 2016 Black-Red, 3LT-Z51 Auto 8-speed.

12-23-2017	#44
Young1 Join Date: Sep 2016 Location: Ocala, FL Posts: 895	Re: WANTED: Cam position sensor and Dual mass flywheel for 1990 ZR1 LT5 I am impressed and thankful for all the expertise and dedication for the sake of everyone that enjoys these cars. This is neat to see it come together. I hope you have good weather for testing. Sent from my iPhone using ZR-1 Net Registry __________________ Steve Young 1991 ZR-1 Quasar Blue Metallic/Black #729 Second Owner 1991 ZR-1 Dark Red Metallic/Black #2040 SOLD 1990 ZR-1 Dark Red Metallic/Saddle #1670 SOLD Double your happiness.....complain half as much.

12-23-2017	#45
tnova Join Date: Oct 2013 Location: Spokane Valley, WA Posts: 115	Re: WANTED: Cam position sensor for LT5 Phil, Once again to the rescue of the LT5. Highly interested in the end result so I may replace the sensor in my LT5 while it's out of the car and prior to installing the cam covers. Tony - Tnova

12-23-2017	#46
Jagdpanzer Join Date: Apr 2007 Location: Northern VA Posts: 2,658	Re: WANTED: Cam position sensor for LT5 Installed the alternative camshaft position sensor on my 94 Z this afternoon and it performed perfectly during garage running tests. Even disconnected the signal wire which immediately triggered code 31 cam sensor failure. Reconnected and all was fine again. Rainy weather here prevented a more thorough road test however, from what I've seen thus far I'm confident it will perform just as well as the OEM sensor. __________________ Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake

12-24-2017	#49
secondchance Join Date: Aug 2006 Location: McLean, VA Posts: 3,721	Re: WANTED: Cam position sensor for LT5 Fantastic job, Phil! So, which model is this sensor originally listed for? Another GM model?