Engine Cleaning - Page 5 - ZR-1 Net Registry Forums

Dylan@Adams · 01-11-2010

Yep I'm in Rancho Cucamonga.

You could always come out to our detail clinic at Stillen Performance... I'll be posting the info here tomorrow.

lfalzarano · 01-06-2015

Actually, any clearcoat safe polishing compound will remove the dirt and stains. Just do small sections at a time and then when you are done, use Maguire's NXT Generation® Tech Wax® 2.0 to make it shine. Carnauba wax will yellow from the heat Same trick goes for your polished wheels

Bob Eyres · 05-24-2015

Quote:

Originally Posted by lfalzarano

Actually, any clearcoat safe polishing compound will remove the dirt and stains. Just do small sections at a time and then when you are done, use Maguire's NXT Generation® Tech Wax® 2.0 to make it shine. Carnauba wax will yellow from the heat Same trick goes for your polished wheels

Thanks, That's probably what I'll do. I went to the Adam's website to order the product, but it wouldn't let me order just one bottle.

At 19.95 a bottle I didn't want to spend $40.00 just to try their product.

I'll buy a clearcoat safe compound off the shelf.

Flyman 27 · 05-21-2017

Anyone trying this? Polishing your engine?
Recently I found a product called "RamRodz". They are like Q-Tips on steroids. They are intended as gun cleaning tools, but they work excellently for polishing hard to reach engine parts.
They range in size from .17 inch dia. up to 1/2 inch dia. They use bamboo sticks that are quite flexible to get into tight places, but strong enough to not break easily. A full selection box contains 680 swabs, so you have enough to last a long time.
I have found many uses for these.

Tripler · 06-02-2017

Quote:

Originally Posted by QB93Z

When I did my engine, it took me about six hours. I removed both front wheels to be able to stand closer to the engine. But, bending over for that long ruined my back and it took about a week to get to where I could move comfortably again. So be careful and take stretching breaks.

Jim

I believe this is were the BL5000 Quick Jack would be perfect . I used it when replacing the window stop on the passenger side of our Z . What a back and knee saver .
I will be using it to clean the engine also . Thanks for the tips Jim and of course Dylan from Adams products also .

Z51JEFF · 06-18-2017

I've found that using anything with abrasives will change the finish anywhere you use it.

90C4ZR1 · 06-26-2017

Just cleaned my LT5 engine to a like new clean with Arm and Hammer Extreme White Toothpaste. About 3 hours labor, 1/2 tube of toothpaste, 1 brush, and a pint spray bottle of water. Going to check out the Maguires NXT wax.

Sent from my SAMSUNG-SM-G900A using ZR-1 Net Registry mobile app

Dynomite · 07-07-2017

Quote:

Originally Posted by xlr8nflorida

I use Toothpaste and distilled water.
Cleans my LT-5 right up and it smells minty fresh

Then I hand dry it with towel and leaf blower to be safe.

A tooth Paste User.....

Quote:

Originally Posted by 90C4ZR1

Just cleaned my LT5 engine to a like new clean with Arm and Hammer Extreme White Toothpaste. About 3 hours labor, 1/2 tube of toothpaste, 1 brush, and a pint spray bottle of water. Going to check out the Maguires NXT wax.

Sent from my SAMSUNG-SM-G900A using ZR-1 Net Registry mobile app

A second Tooth Paste User......

Welcome to the Registry Forum 90C4ZR1

Guess we know what you are driving

I have Number 3032 the last 1990 sold to the public

90C4ZR1 · 07-11-2017

I used Arm and Hammer Extreme Whitening Toothpaste to clean my LT5 to show room look. I used a toothbrush originally, but on doing touchup I used a microfiber cloth on my finger tip, dipped in water, and a dab of toothpaste. Man I was really surprised how good it looks. I rub a bit and spray with water from a spray bottle and dry. Although the toothbrush did the original work, I prefer the microfiber wrapped on my finger. You can actually see the oxidation removed on the cloth. Took me about 3.5 hours of love and labor.

SAB · 08-01-2017

Quote:

Originally Posted by 90C4ZR1

I used Arm and Hammer Extreme Whitening Toothpaste to clean my LT5 to show room look. I used a toothbrush originally, but on doing touchup I used a microfiber cloth on my finger tip, dipped in water, and a dab of toothpaste. Man I was really surprised how good it looks. I rub a bit and spray with water from a spray bottle and dry. Although the toothbrush did the original work, I prefer the microfiber wrapped on my finger. You can actually see the oxidation removed on the cloth. Took me about 3.5 hours of love and labor.

Did the finish on the motor darken up after you used the toothpaste?

01-11-2010	#41
Dylan@Adams Join Date: Jul 2009 Location: SoCal Posts: 407	Re: Engine Cleaning Yep I'm in Rancho Cucamonga. You could always come out to our detail clinic at Stillen Performance... I'll be posting the info here tomorrow. __________________ [CENTER][B]USE COUPON CODE: [SIZE="3"][COLOR="Red"]ZR1[/COLOR][/SIZE] TO RECEIVE 10% OFF YOUR NEXT ORDER AT [url]www.ADAMSPOLISHES.com[/url][/B][/CENTER]

01-06-2015	#42
lfalzarano Join Date: Feb 2011 Location: Clayton, North Carolina Posts: 1,133	Re: Engine Cleaning Actually, any clearcoat safe polishing compound will remove the dirt and stains. Just do small sections at a time and then when you are done, use Maguire's NXT Generation® Tech Wax® 2.0 to make it shine. Carnauba wax will yellow from the heat Same trick goes for your polished wheels

05-21-2017	#44
Flyman 27 Join Date: Apr 2017 Location: Wayne Illinois Posts: 402	Re: Engine Cleaning Anyone trying this? Polishing your engine? Recently I found a product called "RamRodz". They are like Q-Tips on steroids. They are intended as gun cleaning tools, but they work excellently for polishing hard to reach engine parts. They range in size from .17 inch dia. up to 1/2 inch dia. They use bamboo sticks that are quite flexible to get into tight places, but strong enough to not break easily. A full selection box contains 680 swabs, so you have enough to last a long time. I have found many uses for these.

06-18-2017	#46
Z51JEFF Join Date: Dec 2007 Location: Fremont,Ca Posts: 3,073	Re: Engine Cleaning I've found that using anything with abrasives will change the finish anywhere you use it.

06-26-2017	#47
90C4ZR1 Join Date: Jun 2017 Location: US Texas Posts: 3	Re: Engine Cleaning Just cleaned my LT5 engine to a like new clean with Arm and Hammer Extreme White Toothpaste. About 3 hours labor, 1/2 tube of toothpaste, 1 brush, and a pint spray bottle of water. Going to check out the Maguires NXT wax. Sent from my SAMSUNG-SM-G900A using ZR-1 Net Registry mobile app

07-11-2017	#49
90C4ZR1 Join Date: Jun 2017 Location: US Texas Posts: 3	Re: Engine Cleaning I used Arm and Hammer Extreme Whitening Toothpaste to clean my LT5 to show room look. I used a toothbrush originally, but on doing touchup I used a microfiber cloth on my finger tip, dipped in water, and a dab of toothpaste. Man I was really surprised how good it looks. I rub a bit and spray with water from a spray bottle and dry. Although the toothbrush did the original work, I prefer the microfiber wrapped on my finger. You can actually see the oxidation removed on the cloth. Took me about 3.5 hours of love and labor.