WMD 31 October 2010 - Big projects - Page 3 - ZR-1 Net Registry Forums

QB93Z · 10-31-2010

WMD was a great success. We had a nice group of people including guys from New Jersey, Pennsylvania, Maryland and Virginia.

The transmission and Fidanza flywheel install went well. The only glitch was that we could not install the drive shaft with the C-beam bolted in. We had to disconnect the the C-beam at the transmission and move it out of the way to get the drive shaft to clear the edge of the tunnel framing. We haven't had that problem in the past.

We had plenty of supervision:

New flywheel installed:

Initial report from David is "Thumbs Up" for the flywheel , new transmission and shifter.

I replaced the plug wires and coils on my '93. No problems. I did not replace the A/C compressor that was blowing the 10 amp A/C Clutch fuse. The problem turned out to be a pinched wire going to the clutch. Check out the Techinal Section for some pictures.

Scott stopped by with his Z06:

A good time was had by all.

Jagdpanzer · 10-31-2010

Don't you guys think David has some explaining to do as to why the DM flywheel that came out was in such good shape after all the 'spirited" driving miles he has put on it?

Scrrem · 10-31-2010

Quote:

Originally Posted by Aurora40

Well?? So is there a magic bullet for the single-mass flywheel noise?

Yeah, what Bob said!!! So, what's the verdict?
Rich

ZZZZZR1 · 10-31-2010

Quote:

Originally Posted by Scrrem

Yeah, what Bob said!!! So, what's the verdict?
Rich

No rattle! You gotta drive it when I see you!

RICKYRJ1 · 10-31-2010

Hey just got a txt from Dave J. He's stuck on 95S, his transmission fell out of his car and is lying in the middle of the left lane about a half mile back from where he's pulled over.

Maybe Darren can get some of Baltimores bravest to go rescue him.

Looks like another great day for the WAZOO crew, wish I could have made it. I'll catch you guys on the next one.
Looks like Dave has become the Mod King of the SE section.
Why didn't any of my Z brothers take off those heat sheilds? HE doesn't need them with that slick new tranny

Scrrem · 10-31-2010

Quote:

Originally Posted by ZZZZZR1

No rattle! You gotta drive it when I see you!

Can't wait Dave.

Now for the big question....What was the official removal/installation time? We should have a world record time with this being the 6th or 7th transmission for WAZOO!!
Rich

LGAFF · 10-31-2010

Who's who...should really post these in the regular forum too, I think people wold enjoy it

ZZZZZR1 · 10-31-2010

Quote:

Originally Posted by LGAFF

Who's who...should really post these in the regular forum too, I think people wold enjoy it

The corvette.forum?

LGAFF · 10-31-2010

Most people don't read to regionals....should post some pics in the General or Tech Forum

tomtom72 · 11-02-2010

I have just one question.......why Dave are your hands soooo clean? How do you do a trans swap and not have dirty hands?

10-31-2010	#21
QB93Z Join Date: May 2007 Location: Westminster, Maryland Posts: 3,689	Re: WMD 31 October 2010 - Big projects WMD was a great success. We had a nice group of people including guys from New Jersey, Pennsylvania, Maryland and Virginia. The transmission and Fidanza flywheel install went well. The only glitch was that we could not install the drive shaft with the C-beam bolted in. We had to disconnect the the C-beam at the transmission and move it out of the way to get the drive shaft to clear the edge of the tunnel framing. We haven't had that problem in the past. We had plenty of supervision: New flywheel installed: Initial report from David is "Thumbs Up" for the flywheel , new transmission and shifter. I replaced the plug wires and coils on my '93. No problems. I did not replace the A/C compressor that was blowing the 10 amp A/C Clutch fuse. The problem turned out to be a pinched wire going to the clutch. Check out the Techinal Section for some pictures. Scott stopped by with his Z06: A good time was had by all. __________________ If it isn't fun, you aren't doing it right! 1990 Black ZR-1 - sold 1993 Quasar Blue ZR-1 1994 Competition Yellow ZR-1 1995 Dark Purple ZR-1 Maryland State Coordinator WAZOO Member

10-31-2010	#22
Jagdpanzer Join Date: Apr 2007 Location: Northern VA Posts: 2,661	Re: WMD 31 October 2010 - Big projects Don't you guys think David has some explaining to do as to why the DM flywheel that came out was in such good shape after all the 'spirited" driving miles he has put on it?

10-31-2010	#25
RICKYRJ1 Join Date: Dec 2005 Location: Tinton Falls, NJ Posts: 1,177	Re: WMD 31 October 2010 - Big projects Hey just got a txt from Dave J. He's stuck on 95S, his transmission fell out of his car and is lying in the middle of the left lane about a half mile back from where he's pulled over. Maybe Darren can get some of Baltimores bravest to go rescue him. Looks like another great day for the WAZOO crew, wish I could have made it. I'll catch you guys on the next one. Looks like Dave has become the Mod King of the SE section. Why didn't any of my Z brothers take off those heat sheilds? HE doesn't need them with that slick new tranny

10-31-2010	#27
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: WMD 31 October 2010 - Big projects Who's who...should really post these in the regular forum too, I think people wold enjoy it __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

10-31-2010	#29
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: WMD 31 October 2010 - Big projects Most people don't read to regionals....should post some pics in the General or Tech Forum __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

11-02-2010	#30
tomtom72 Join Date: Dec 2004 Location: Jacksonville, FL USA Posts: 4,645	Re: WMD 31 October 2010 - Big projects I have just one question.......why Dave are your hands soooo clean? How do you do a trans swap and not have dirty hands? __________________ 1990 ZR-1, Black/grey, #2233, stock. ZR-1 Net Reg Founding Member #316 & NCM member