4 Corner Winter Project - Page 2 - ZR-1 Net Registry Forums

XfireZ51 · 12-14-2015

Thought I'd start a new thread since my other one has expanded beyond just new rubber. We're moving onto reducing rotational mass w lighter rotors, plus upgrading rear trailing arm mounts and tie rod brackets.

Had discussion w Pete on possibly massaging the cylinder heads some more, but our concensus was that motor feels pretty strong right now. Bang for the buck not as strong as maybe looking in other areas. With updating my Invos to
Mich SS, I started looking into the whole rotational mass thing. Seems that this is an area that would yield better results in terms of ROI. The Michelins will add a total of 10lbs over current tires. Also, the Z06 brakes are large w front rotors weighing in at 28lbs. ea./rears 20lbs. ea.
Been researching the alternative rotors and have found two that look up to the task. The preferred rotors by the Z06 crowd is the Coleman 2pc. rotors built by Performance AFX. These rotors weigh 17F/15R. They basically reduce rotating mass by 30lbs overall w 20lbs coming off the front end. Rule of thumb is 1lb ~1hp. On the dyno that should mean about an 8-10hp pickup since the front wheels aren't going anywhere.
However, the mitigating factor is that the new rear tires will be ADDING a total of 6lbs. The rear weight loss will net out at 4lbs. The net weight loss on the front after new tires will be 16lbs for an overall net weight reduction of 20lbs.
Pickup of 20hp to the wheels would be huge. Other benefits are quicker steering and shorter braking distances.

Rear Rotors(pic) are made to accommodate the Z06 eBrake. Side view is of front rotor.

12-14-2015	#1
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,691	4 Corner Winter Project Thought I'd start a new thread since my other one has expanded beyond just new rubber. We're moving onto reducing rotational mass w lighter rotors, plus upgrading rear trailing arm mounts and tie rod brackets. Had discussion w Pete on possibly massaging the cylinder heads some more, but our concensus was that motor feels pretty strong right now. Bang for the buck not as strong as maybe looking in other areas. With updating my Invos to Mich SS, I started looking into the whole rotational mass thing. Seems that this is an area that would yield better results in terms of ROI. The Michelins will add a total of 10lbs over current tires. Also, the Z06 brakes are large w front rotors weighing in at 28lbs. ea./rears 20lbs. ea. Been researching the alternative rotors and have found two that look up to the task. The preferred rotors by the Z06 crowd is the Coleman 2pc. rotors built by Performance AFX. These rotors weigh 17F/15R. They basically reduce rotating mass by 30lbs overall w 20lbs coming off the front end. Rule of thumb is 1lb ~1hp. On the dyno that should mean about an 8-10hp pickup since the front wheels aren't going anywhere. However, the mitigating factor is that the new rear tires will be ADDING a total of 6lbs. The rear weight loss will net out at 4lbs. The net weight loss on the front after new tires will be 16lbs for an overall net weight reduction of 20lbs. Pickup of 20hp to the wheels would be huge. Other benefits are quicker steering and shorter braking distances. Rear Rotors(pic) are made to accommodate the Z06 eBrake. Side view is of front rotor. __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX Last edited by XfireZ51; 03-08-2024 at 02:10 PM.