Inj 1 fues keeps blowing - Page 2 - ZR-1 Net Registry Forums

LGAFF · 01-25-2016

So with the plenum off, and Ignition module and coil housing connected, I could not get the fuse to blow...has to be an inj wire...but I see nothing

tested with power on, all inj had power to the wire

-=Jeff=- · 01-25-2016

Ohm out the base with the coils off and base disconnected form car. check each line for shorts

where do the 4 hot coil wires go from the base, follow and check those. Since the fuse pops on key on, engine not running. disconnect the injectors try again.

What about the injector modules? is there one form primary and one for secondary?

electrical is not as easy as swapping parts, might be in the wire

LGAFF · 01-25-2016

checked all of the fuel injectors, going to replace all of the coils this weekend, will also go through the injector harness.

cvette98pacecar · 01-25-2016

Quote:

Originally Posted by LGAFF

checked all of the fuel injectors, going to replace all of the coils this weekend, will also go through the injector harness.

Lee, the plunger inside the injector is jammed. It is not moving with the PWM which is creating a large load on the circuit which is blowing the fuse.

tpepmeie · 01-26-2016

Quote:

Originally Posted by cvette98pacecar

Lee, the plunger inside the injector is jammed. It is not moving with the PWM which is creating a large load on the circuit which is blowing the fuse.

There would be no PWM or plunger activation with Key on, Engine Off. That's when he said the fuse is blowing.

cvette98pacecar · 01-31-2016

Dah, Read first comment second. For whatever reason I thought the car was running.

LGAFF · 10-09-2016

INJ 1 fuse issue is back; It is tied in the coil plug ins/DIS somehow....at first it seemed to be the Crank sensor as the fuse only blew with the crank sensor was plugged into the DIS....then it suddenly stopped

Wonder if the wire is grounded out were it travels around the engine/frame

-=Jeff=- · 10-09-2016

you have a chafed wire that is shorting.. doesn't always happen, but sucks when it does.

I hate looking for those, good luck

GOLDCYLON · 10-09-2016

Quote:

Originally Posted by LGAFF

INJ 1 fuse issue is back; It is tied in the coil plug ins/DIS somehow....at first it seemed to be the Crank sensor as the fuse only blew with the crank sensor was plugged into the DIS....then it suddenly stopped

Wonder if the wire is ground out were it travels around the engine/frame

You may need to pull those harnesses apart like Cliff did in his write up. However his issue was in the injector harness Lee. I spoke with him last night about it. Since he has done that his problem in his 95 has went away. GC

LGAFF · 10-09-2016

Quote:

Originally Posted by GOLDCYLON

You may need to pull those harnesses apart like Cliff did in his write up. However his issue was in the injector harness Lee. I spoke with him last night about it. Since he has done that his problem in his 95 has went away. GC

Did that already on the inj......but its not the injectors its in the DIS/Crank sensor

01-25-2016	#11
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Inj 1 fues keeps blowing So with the plenum off, and Ignition module and coil housing connected, I could not get the fuse to blow...has to be an inj wire...but I see nothing tested with power on, all inj had power to the wire __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359 Last edited by LGAFF; 01-25-2016 at 02:56 PM.

01-25-2016	#12
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,153	Re: Inj 1 fues keeps blowing Ohm out the base with the coils off and base disconnected form car. check each line for shorts where do the 4 hot coil wires go from the base, follow and check those. Since the fuse pops on key on, engine not running. disconnect the injectors try again. What about the injector modules? is there one form primary and one for secondary? electrical is not as easy as swapping parts, might be in the wire __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978

01-25-2016	#13
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Inj 1 fues keeps blowing checked all of the fuel injectors, going to replace all of the coils this weekend, will also go through the injector harness. __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

01-31-2016	#16
cvette98pacecar Join Date: May 2011 Location: Sydney, Australia Posts: 2,479	Re: Inj 1 fues keeps blowing Dah, Read first comment second. For whatever reason I thought the car was running. __________________ Robert J. DeMarco [SIGPIC][/SIGPIC] [COLOR=blue]G[/COLOR][COLOR=red]rand[/COLOR] [COLOR=blue]S[/COLOR][COLOR=red]port[/COLOR] Registry Lifetime Member NCM Lifetime Member #2655 Pacecar Registry Member [COLOR=red]ZOOM Charter Member - ZR-1 Owners of Michigan[/COLOR] [COLOR=plum][I]ZR-1[/I] Registry member since 2012 [/COLOR] [COLOR=black]1990 LPE "368" Aerobody ZR-1, Last ZR-1 built by John[/COLOR] 1991 Callaway Aerobody ZR-1, DRM 500 1991 Shinoda Aerobody Spyder, 1998 Pace Car

10-09-2016	#17
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Inj 1 fues keeps blowing INJ 1 fuse issue is back; It is tied in the coil plug ins/DIS somehow....at first it seemed to be the Crank sensor as the fuse only blew with the crank sensor was plugged into the DIS....then it suddenly stopped Wonder if the wire is grounded out were it travels around the engine/frame __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359 Last edited by LGAFF; 10-09-2016 at 11:23 PM.

10-09-2016	#18
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,153	Re: Inj 1 fues keeps blowing you have a chafed wire that is shorting.. doesn't always happen, but sucks when it does. I hate looking for those, good luck __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978