Finally installed my M1 Prowler and Big Mouth Air Dam - Page 2 - ZR-1 Net Registry Forums

03-11-2009

Thanks again for all the comments. I can't wait to get it on the road as it seems like it has been forever. I still have much to do, but trying to get focused.

Aloha!

03-11-2009

Quote:

Originally Posted by GOLDCYLON

Yes I did not understand why the stainless screen did not extend correctly to both sides of the air dam. (Shame as it was very well constructed) However, I beleive the intent was to keep the big debris out such as leaves and white plastic bags and such and I can clearly state in that reguards it works as advertised. I too was unhappy with the mount and just moved it to straddle the middle of the Dam. Actually it did not come out too bad. After recently doing my radiator I can easily say something to protect against what I found in my radiator shroud area is better than no solution. Enjoy. GC

GC,

I'm going to try to figure a nice way to get it mounted and agree with you. I think I am going to ask Eric about the why on the size and the mounting location. I almost was going to pc it black, but did not want to waste the cash on it since it was not custom fitted nicely.

Thanks again!

GOLDCYLON · 03-12-2009

Quote:

Originally Posted by HAWAIIZR-1

GC,

I'm going to try to figure a nice way to get it mounted and agree with you. I think I am going to ask Eric about the why on the size and the mounting location. I almost was going to pc it black, but did not want to waste the cash on it since it was not custom fitted nicely.

Thanks again!

Craig I will send you a pic of what I did if interested. GC

03-12-2009

Quote:

Originally Posted by GOLDCYLON

Craig I will send you a pic of what I did if interested. GC

Okay, thanks. I'll PM you with address. I happened to be looking at it last night to figure out a better way to mount a nice screen (black) in there.

Aloha,
Craig

GrayZ · 03-12-2009

Craig, I bought my side vent inserts from Mercado industries
they also offer, sreens and such, ya might check em out bro.

http://www.c4dhr.com/

GOLDCYLON · 03-12-2009

Craig for my BMAD Screen insert I used the center support brace for more stability as well. I simply placed the screen centered on the backside edge. I think it came ok its not angled but my arm was while underneath. GC

03-13-2009

Quote:

Originally Posted by ITLGO2

Craig, I bought my side vent inserts from Mercado industries
they also offer, sreens and such, ya might check em out bro.

http://www.c4dhr.com/

Thanks Keith. You might not remember that I had those side vent inserts on mine too. I think I might go custom with my own, especially since I have a different spoiler and the BMAD. I would be afraid I would have to mess with it or be disappointed. They do make some good stuff though.

Thanks again

03-13-2009

Quote:

Originally Posted by GOLDCYLON

Craig for my BMAD Screen insert I used the center support brace for more stability as well. I simply placed the screen centered on the backside edge. I think it came ok its not angled but my arm was while underneath. GC

GC,

That looks great and you did a good job with it. I'll try and play with it more to see if can get a nice fit with theirs before I move on to try something else. It seems the mounting tabs for the center deflector could be a good mounting place if I decided to go with something else and will relook using the center support brace too.

Thanks again!!!

03-11-2009	#11
HAWAIIZR-1 Guest Posts: n/a	Re: Finally installed my M1 Prowler and Big Mouth Air Dam Thanks again for all the comments. I can't wait to get it on the road as it seems like it has been forever. I still have much to do, but trying to get focused. Aloha!

03-12-2009	#15
GrayZ Join Date: Mar 2006 Location: Innsbrook, Missouri Posts: 1,727	Re: Finally installed my M1 Prowler and Big Mouth Air Dam Craig, I bought my side vent inserts from Mercado industries they also offer, sreens and such, ya might check em out bro. http://www.c4dhr.com/

03-12-2009	#16
GOLDCYLON Join Date: May 2007 Location: Peoria, AZ Posts: 9,153	Re: Finally installed my M1 Prowler and Big Mouth Air Dam Craig for my BMAD Screen insert I used the center support brace for more stability as well. I simply placed the screen centered on the backside edge. I think it came ok its not angled but my arm was while underneath. GC __________________ GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V