|
04-07-2022
|
#11 |
 Join Date: Jul 2016
Location: Harrodsburg, KY
Posts: 436
|
Re: 1990 ZR-1 #2456 Original Components
Delivered with, assembly line air filter...
   
|
|
|
|
04-07-2022
|
#12 |
 
Join Date: Sep 2008
Location: Mullica Hill, New Jersey
Posts: 2,592
|
Re: 1990 ZR-1 #2456 Original Components
GREAT pictures!!!
INTERESTING!!! Puzzled about the top. The masking tape was done at the factory, and should match the last numbers of VIN. They should be stamped on the roof frame as well. If the stamped number equals the VIN that would be good, but still would not explain the 470 on the tape. Switched / mismatched at dealer perhaps?? Thanks for sharing the pictures with the progress!!  Marty |
|
|
|
|
04-07-2022
|
#13 |
|
Join Date: Jul 2016
Location: Harrodsburg, KY
Posts: 436
|
Re: 1990 ZR-1 #2456 Original Components
I've searched for the VIN on the plexi top. Obviously not looking in the proper area.
I have another 90 with two tops (44 miles) and I found the VIN. The other 90 has different markings, if I remember correctly. I'll wonder down stairs and get a shot of it, later. I tried to make sense of the # on the tape but am just going to leave well enough alone. Several pieces of old masking tape in the car. I'm trying not to disturb what's there. |
|
|
|
|
04-07-2022
|
#14 |
|
Join Date: Jul 2016
Location: Harrodsburg, KY
Posts: 436
|
Re: 1990 ZR-1 #2456 Original Components
There is an ID label on the rear fiberglass spring. It is on the top driver side. Lousy pic...
 
|
|
|
|
|
04-07-2022
|
#15 |
Join Date: Oct 2017
Location: TX
Posts: 2,036
|
Re: 1990 ZR-1 #2456 Original Components
Quote from Marty :
INTERESTING!!! Puzzled about the top. The masking tape was done at the factory, and should match the last numbers of VIN. They should be stamped on the roof frame as well. If the stamped number equals the VIN that would be good, but still would not explain the 470 on the tape. Switched / mismatched at dealer perhaps?? (End Quote) Marty, The glass top for my '90 has that piece of masking tape on it also. Written on the tape is "987". The number of my car is "0442" and the "0442" is also stamped in the frame of the glass top in the proper place. I've often wondered why the masking tape was there and why is was marked as it is. Here's a pic: 1217-6.jpg
__________________
Kenny 1990 #442 
Last edited by TX '90 ZR1; 04-07-2022 at 06:44 PM. Reason: spelling |
|
|
|
|
04-07-2022
|
#16 |
|
Join Date: Jul 2016
Location: Harrodsburg, KY
Posts: 436
|
Re: 1990 ZR-1 #2456 Original Components
Kenny
What is the info on the center rear portion of your glass top? Is it Almac? Regards, Mark PS...I enjoy a good mystery |
|
|
|
|
04-07-2022
|
#17 |
|
Join Date: Sep 2008
Location: Mullica Hill, New Jersey
Posts: 2,592
|
Re: 1990 ZR-1 #2456 Original Components
If either of you have the build sheet, perhaps it is the sequence number of the build.
Later cars seem to match. Perhaps 90 was different? Will refer to a C-4 NCRS Judge to see if they have any insight. I too enjoy ZR-1 history mystery. Great to see the AC Spark Plug markings. Appreciate the pictures! Very good progress! Marty |
|
|
|
|
04-07-2022
|
#18 |
|
Join Date: Jul 2016
Location: Harrodsburg, KY
Posts: 436
|
Re: 1990 ZR-1 #2456 Original Components
I have the build sheet for my other low mile ZR-1 but, dagnabbit, now I'm gonna have to remove the bronze top to see the tape #😜
Always something. Tomorrow, I'll get that done 👍 |
|
|
|
|
04-07-2022
|
#19 |
Join Date: Dec 2019
Location: st louis mo
Posts: 749
|
Re: 1990 ZR-1 #2456 Original Components
We're is the stamping on the top at?
__________________
95 admiral blue z(sold)/ / 93 ruby z(sold) 91 steel blue z/95 aqua z haibeck 510, 91 callaway 415 areobody #5 |
|
|
|
|
04-07-2022
|
#20 | |
|
Join Date: Oct 2017
Location: TX
Posts: 2,036
|
Re: 1990 ZR-1 #2456 Original Components
Quote:
I'll have to unwrap it and look. Will let you know.
__________________
Kenny 1990 #442
|
|
|
|
|
 |
|
|
Linear Mode
