carter200's CNC machining is............ - Page 3 - ZR-1 Net Registry Forums

secondchance · 06-09-2009

Quote:

Originally Posted by -=Jeff=-

Yes, much more controlable over rough roads, car did not dart like it did before

Yes, front shocks are the new pair that was on eBay for $150.. I had those grooved for the shocks

I need too get good pictures but the front is lowered 1.5" and the rear (still has the fiberglass spring) is lowered 1.25"

Hmmm, Another future project.

Thanks.

secondchance · 06-09-2009

One major concern I have over supension mod is that, based on what I understand, changes in spring rate and/or roll bar can result in under steer/over steer characteristic.
Will you be testing and tweaking?

-=Jeff=- · 06-09-2009

Quote:

Originally Posted by secondchance

One major concern I have over supension mod is that, based on what I understand, changes in spring rate and/or roll bar can result in under steer/over steer characteristic.
Will you be testing and tweaking?

probably tweaking, I need to finish my poly bushing install and get the car aligned.. then I will see how well it does

secondchance · 06-09-2009

Quote:

Originally Posted by -=Jeff=-

probably tweaking, I need to finish my poly bushing install and get the car aligned.. then I will see how well it does

Please keep us updated.

-=Jeff=- · 06-09-2009

Quote:

Originally Posted by secondchance

Please keep us updated.

will do.. keep in mind.. it is a slow going process with me

bobbyhi · 06-17-2009

Forgot to post some pics of the air filter bolts that Carter made - hope this works

DaveK · 06-17-2009

Very nice Bob! And Carter!

carter200 · 06-17-2009

Quote:

Originally Posted by DaveK

Very nice Bob! And Carter!

Thanks Bob and DaveK

Bob, you gonna line em up or let em end up where they will? Either way they look nice. Thanks again

rkreigh · 06-18-2009

how is the ride in comparison to before

I went with 400 front, and 275 back and the ride is OK, but I think the F1 supercars are the "problem"

biggest thing I ran into is lowering the car too much. not good. I think I was bottoming out the shocks as I busted a fx3 controller

I'd like to someday upgrade to a better shock and maybe lose the fx3.

more hassle than it's worth to me.

nice setup!! that's a great way to go as coil overs are expensive and you really engineered a bargain conversion

FYI, DRM grooves the shocks pretty reasonable for the snap ring. a local machine shop quoted me 200 and DRM was 15 per shock as I remember (call randy)

as for tuning, it's hard to "out engineer" the Gm engineers and the stock suspension is actually a pretty good compromize for street driving, but the coil overs definely help

there is a bit of hassle getting them on there and setup, and because I'm so lazy I wouldn't have done it again knowing what I do now, but I mostly didn't like the expense and the harsh ride. there is no doubt the car is "glued down" better and much more stable at speed around corners.

my c5 has coil overs, but rides like a cadillac in comparison

alot of that is the EMTs though, when I bolt on my "race tires" with the a molds, ride is much better.

-=Jeff=- · 06-18-2009

Ron,

How low did you go? I have not noticed if it bottoms out, but the stance it very close to what my 89 was.. it seems much better.. as for the ride, I have not driven enough to say how it really is.. I have one more component to swap, then get an alignment.. Not sure i will get the new parts on this weekend but I am hoping to

06-09-2009	#22
secondchance Join Date: Aug 2006 Location: McLean, VA Posts: 3,723	Re: carter200's CNC machining is............ One major concern I have over supension mod is that, based on what I understand, changes in spring rate and/or roll bar can result in under steer/over steer characteristic. Will you be testing and tweaking?

06-17-2009	#26
bobbyhi Join Date: Jul 2005 Location: Mendota Heights, MN. 55120 Posts: 984	Re: carter200's CNC machining is............ Forgot to post some pics of the air filter bolts that Carter made - hope this works __________________ Bob Anderson 1990 #2405 White/Gray Haibeck chip,4:09 gears,Power Effects Exhaust,5 spoke chrome,C5 brakes,49th Street rockers,K&N,Hurst,Headers,Upper & lower ported Minnesota State Director Founding Member #19

06-17-2009	#27
DaveK Join Date: Jul 2004 Location: Sudbury, Ontario. Canada Posts: 1,538	Re: carter200's CNC machining is............ Very nice Bob! And Carter! __________________ 1991 #1516 Black/Black davidmkelly.com "Speed is often confused with insight." - Johan Cruijff

06-18-2009	#29
rkreigh Join Date: Jan 2004 Location: Alex VA Posts: 1,087	Re: carter200's CNC machining is............ how is the ride in comparison to before I went with 400 front, and 275 back and the ride is OK, but I think the F1 supercars are the "problem" biggest thing I ran into is lowering the car too much. not good. I think I was bottoming out the shocks as I busted a fx3 controller I'd like to someday upgrade to a better shock and maybe lose the fx3. more hassle than it's worth to me. nice setup!! that's a great way to go as coil overs are expensive and you really engineered a bargain conversion FYI, DRM grooves the shocks pretty reasonable for the snap ring. a local machine shop quoted me 200 and DRM was 15 per shock as I remember (call randy) as for tuning, it's hard to "out engineer" the Gm engineers and the stock suspension is actually a pretty good compromize for street driving, but the coil overs definely help there is a bit of hassle getting them on there and setup, and because I'm so lazy I wouldn't have done it again knowing what I do now, but I mostly didn't like the expense and the harsh ride. there is no doubt the car is "glued down" better and much more stable at speed around corners. my c5 has coil overs, but rides like a cadillac in comparison alot of that is the EMTs though, when I bolt on my "race tires" with the a molds, ride is much better. __________________ 95 390 LPE ZR1 (505 rwhp) LSV = Lingenfelter Super Vette Twin Turbo 2003 Z06 (800 RWHP)

06-18-2009	#30
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,169	Re: carter200's CNC machining is............ Ron, How low did you go? I have not noticed if it bottoms out, but the stance it very close to what my 89 was.. it seems much better.. as for the ride, I have not driven enough to say how it really is.. I have one more component to swap, then get an alignment.. Not sure i will get the new parts on this weekend but I am hoping to __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978