B&B exhaust install ?? - ZR-1 Net Registry Forums

32valvZ · 04-01-2008

My new set-up should be here tomorrow according to UPS

.......I noticed that there are no fastening points for the spring hangers on the B&B like on the stock set-up. Does it just use the cat outlets and the 2 muffler hangers?

Zr1 Destroyer · 04-01-2008

You should have the two hangers on the rear aswell as the tail of the tranny orrrr are you talking about something else?

Zr1 Destroyer · 04-01-2008

Quote:

Originally Posted by 32valvZ

My new set-up should be here tomorrow according to UPS

.......I noticed that there are no fastening points for the spring hangers on the B&B like on the stock set-up. Does it just use the cat outlets and the 2 muffler hangers?

Ahhhh...I re-read your post...lol...just the two cat outlets and the factory hangers.....just like factory.

32valvZ · 04-01-2008

So, I'm eliminating any of the spring type hangers?
Only using the two at the mufflers other than where the two pipes in front of the resonator go to the cats...yes?
Thanks, John

Zr1 Destroyer · 04-01-2008

Quote:

Originally Posted by 32valvZ

So, I'm eliminating any of the spring type hangers?
Only using the two at the mufflers other than where the two pipes in front of the resonator go to the cats...yes?
Thanks, John

The spring hangers stay. Other then that it just goes right where the factory deals went.

32valvZ · 04-02-2008

Ok, I looked at the pics again...I see one of the tabs, so there must be 3 more.....I hope!

04-01-2008	#1
32valvZ Join Date: Nov 2007 Location: Sunshine State Posts: 1,071	B&B exhaust install ?? My new set-up should be here tomorrow according to UPS .......I noticed that there are no fastening points for the spring hangers on the B&B like on the stock set-up. Does it just use the cat outlets and the 2 muffler hangers? __________________ [B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B]

04-01-2008	#2
Zr1 Destroyer Join Date: Oct 2005 Location: Candy Apple...yUmMy Posts: 1,137	Re: B&B exhaust install ?? You should have the two hangers on the rear aswell as the tail of the tranny orrrr are you talking about something else?

04-01-2008	#4
32valvZ Join Date: Nov 2007 Location: Sunshine State Posts: 1,071	Re: B&B exhaust install ?? So, I'm eliminating any of the spring type hangers? Only using the two at the mufflers other than where the two pipes in front of the resonator go to the cats...yes? Thanks, John __________________ [B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B]

04-02-2008	#6
32valvZ Join Date: Nov 2007 Location: Sunshine State Posts: 1,071	Re: B&B exhaust install ?? Ok, I looked at the pics again...I see one of the tabs, so there must be 3 more.....I hope! __________________ [B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B]