![]() |
#11 |
Join Date: Apr 2009
Location: ITALY
Posts: 264
|
![]()
I had the same problem some years ago...change the starter and the problem was solved...
|
![]() |
![]() |
![]() |
#12 |
![]() Join Date: Oct 2016
Location: Shepparton. Vic. Australia
Posts: 137
|
![]()
Only driven the car on a few short trips since putting in the new battery, but l haven?t had a problem so far. Odd, because the car started every time and never seemed to lack power while cranking at cold start.. But when hot, it would not even crank. New battery seems to have fixed the issue. Happy days🍻
|
![]() |
![]() |
![]() |
#13 |
Join Date: Mar 2021
Location: Crawfordville, FL
Posts: 216
|
![]()
The reason a new battery has worked so far to correct this problem is that it may put out a higher amp surge to overcome the resistance of the corroded/worn solenoid contact surfaces. The problem still emanates from the starter solenoid and the new battery has temporarily solved that issue.
|
![]() |
![]() |
![]() |
#14 | |
![]() Join Date: Oct 2016
Location: Shepparton. Vic. Australia
Posts: 137
|
![]() Quote:
Cheers, Russell |
|
![]() |
![]() |
![]() |
#15 |
Join Date: Jun 2022
Location: Arroyo Grande CA
Posts: 8
|
![]()
Ozruss90, Just had the same problem mate. I just shipped a 94 ZR1 to Australia, when it came out of the container it wouldn't start. Even with a jump pack...
Installed a new battery and have not had a problem yet. Just thought id add my 2 cents mate. Good luck. Jay. |
![]() |
![]() |
![]() |
#16 | |
![]() Join Date: Oct 2016
Location: Shepparton. Vic. Australia
Posts: 137
|
![]() Quote:
Good to see another Z in Oz 👍 Are you in Oz or CA ? I still believe my problem is starter solenoid contacts, which I will rectify soon, even though it hasn?t let me down since the new battery went in. Mine always started when cold / cool, but not when hot. Cheers, Russell. |
|
![]() |
![]() |
![]() |
#17 | |
Join Date: Jun 2022
Location: Arroyo Grande CA
Posts: 8
|
![]() Quote:
I fear that the contacts are part of my problem too, but for the moment its working fine. I never had a problem starting it either hot or cold when i had it in CA. Anyway, anything can be fixed right? Where are you located mate? Jay. |
|
![]() |
![]() |
![]() |
#18 | |
![]() Join Date: Oct 2016
Location: Shepparton. Vic. Australia
Posts: 137
|
![]() Quote:
I?m in Shepparton, Vic I will be contacting Gerry?s Gaskets soon to get what l need to remove the plenum and sort the suspected problem solenoid contacts. Will you dad have the Z sorted in time for the Corvette Nationals held in Ballarat at the end of March. Would be good to catch up with him as l will be there with my Z. Cheers, From the Mexican state of Victoria, Down Under Russell. |
|
![]() |
![]() |
![]() |
#19 |
Join Date: Jun 2022
Location: Arroyo Grande CA
Posts: 8
|
![]()
Russell, Dad is located in Wangaratta, not too far huh! Small world!
He will have it rego'd by then for sure. I will word him up and you guys should definitely meet up. |
![]() |
![]() |
![]() |
#20 |
![]() Join Date: Sep 2008
Location: Speedway, IN
Posts: 128
|
![]()
I got caught twice by this earlier this year. Believe it was oxidation on ignition switch contacts or just dummy me not pushing the key in far enough. If it happens again, look for the security light blinking. That will kill the starter circuit.
Sent from my iPhone using ZR-1 Net Registry |
![]() |
![]() |
![]() |
|
|