Just another one... "pumping" cruise control - ZR-1 Net Registry Forums

Matt B · 04-25-2021

While I took her for another spin today I discovered another unexpected behavior. When using cruise control I recognized a "pulsating" motion of the car. First I thought it may be because of very low RPM and rather low speed. Later on the Autobahn I realized that even the gas pedal slightly but very noticeably moves in and out about 2 times a second. This motion is very constant and seems to happen at all (engine) speeds.

Can it be a result of my recent speedo adjustment via module by Ecklers? To offset my 335/35 rear tires I accelerated the signal by 2%. Speedo is back to GPS correct reading now.
Or would you rather suspect a vacuum issues? Or something else?

BigJohn · 04-27-2021

Not unusual for manual cars back then.

Paul Workman · 05-05-2021

I don't have the answer.

But, far as troubleshooting goes, I'd want to start with the all connectors leading to/from the cruise module (including power and ground connections. And, if they were all satisfactory and cleaned if necessary, and if that had no change, then I'd want to see if reinstalling the stock speedo calibration (chip) would solve the pulsing. And, do you have a the ability to do a scan to see what else is going.

Ultimately, you might want to swap out the cruise module for another module, if possible. And, if that results in fixing the problem, you have our answer and maybe BATEE (?) might be able to fix it (unless you are electronically inclined yourself!)

secondchance · 05-06-2021

I would be tempted to hook up vacuum pump/gauge on cruise control unit (near the brake booster), create vacuum and see if it holds. Never had it happen to me but if there is a slow leak, I wonder, could result in pulsing.

Matt B · 05-06-2021

That's what I'll do next. A ZR friend here in Germany who already helped me out with other stuff indicated that it might well be an effect of the speedo calibration box. Which makes sense in case the cruise control box expects a certain ratio of RPM and speed reading. I may have to play around with calibration, too.
Unfortunately I had no chance to try the cruise control with the original tires.

Sent from my J9110 using ZR-1 Net Registry mobile app

WARP TEN · 05-07-2021

The first time I had the rear gears changed to 4.10s (on the '93), I used an electronic speed calibration device (can't remember what brand). I had the same cruise control variance issue. Dumped the electronic unit and had Marc install the proper speedo gears and never had the problem after that. Ditto on the '95, which got the speedo gears at the same time as the 4.10s. --Bob

04-25-2021	#1
Matt B Join Date: Jan 2021 Location: Beautiful Bavaria Posts: 523	Just another one... pulsating cruise control While I took her for another spin today I discovered another unexpected behavior. When using cruise control I recognized a "pulsating" motion of the car. First I thought it may be because of very low RPM and rather low speed. Later on the Autobahn I realized that even the gas pedal slightly but very noticeably moves in and out about 2 times a second. This motion is very constant and seems to happen at all (engine) speeds. Can it be a result of my recent speedo adjustment via module by Ecklers? To offset my 335/35 rear tires I accelerated the signal by 2%. Speedo is back to GPS correct reading now. Or would you rather suspect a vacuum issues? Or something else? __________________ ZR-1 #638/1991 Last edited by Matt B; 04-26-2021 at 11:08 AM.

04-27-2021	#2
BigJohn Join Date: Feb 2012 Location: Ledyard,CT Posts: 8,245	Re: Just another one... "pumping" cruise control Not unusual for manual cars back then.

05-05-2021	#3
Paul Workman Join Date: Nov 2007 Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri Posts: 6,493	Re: Just another one... "pumping" cruise control I don't have the answer. But, far as troubleshooting goes, I'd want to start with the all connectors leading to/from the cruise module (including power and ground connections. And, if they were all satisfactory and cleaned if necessary, and if that had no change, then I'd want to see if reinstalling the stock speedo calibration (chip) would solve the pulsing. And, do you have a the ability to do a scan to see what else is going. Ultimately, you might want to swap out the cruise module for another module, if possible. And, if that results in fixing the problem, you have our answer and maybe BATEE (?) might be able to fix it (unless you are electronically inclined yourself!) __________________ Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry

05-06-2021	#4
secondchance Join Date: Aug 2006 Location: McLean, VA Posts: 3,723	Re: Just another one... "pumping" cruise control I would be tempted to hook up vacuum pump/gauge on cruise control unit (near the brake booster), create vacuum and see if it holds. Never had it happen to me but if there is a slow leak, I wonder, could result in pulsing.

05-06-2021	#5
Matt B Join Date: Jan 2021 Location: Beautiful Bavaria Posts: 523	Re: Just another one... pulsating cruise control That's what I'll do next. A ZR friend here in Germany who already helped me out with other stuff indicated that it might well be an effect of the speedo calibration box. Which makes sense in case the cruise control box expects a certain ratio of RPM and speed reading. I may have to play around with calibration, too. Unfortunately I had no chance to try the cruise control with the original tires. Sent from my J9110 using ZR-1 Net Registry mobile app __________________ ZR-1 #638/1991

05-07-2021	#6
WARP TEN Join Date: Apr 2007 Location: Lake Bluff, IL Posts: 2,094	Re: Just another one... "pumping" cruise control The first time I had the rear gears changed to 4.10s (on the '93), I used an electronic speed calibration device (can't remember what brand). I had the same cruise control variance issue. Dumped the electronic unit and had Marc install the proper speedo gears and never had the problem after that. Ditto on the '95, which got the speedo gears at the same time as the 4.10s. --Bob __________________ 2016 Long Beach Red Z06 #10281 "POPS Z" 1995 Polo Green #409 "WARP TEN"--Haibeck 350/510 package, 4.10s, Hurst, Stock Exhaust with QTP Cutouts --Sold but still running strong 1993 Quasar Blue #161 "HIL KING" --Sold but still running strong, now with more than 120,000 miles 1967 Marlboro Maroon/Saddle Corvette Coupe 300 hp/4-spd --Sold a long time ago ZR-1 Net Registry Founding Member #95 NCM Lifetime Member Favorite Quote--Attributed to Mickey Thompson: "Too Much Horsepower is Almost Enough"