|
06-14-2020
|
#1 |
|
Join Date: Aug 2005
Location: Fishers, IN
Posts: 814
|
RH oem harness routing
This is a long shot, but does anybody have a good photo(s) of the factory lower wiring harness routing. Ideally on an original car or close to it. Doing a resto and struggling to route the crank position, oil level sensor and passenger O2 wiring.
It?s a 93, so the cats are removed. Which gives me some access. I just don?t have any original photos. Thanks. Sent from my iPhone using ZR-1 Net Registry
__________________
Todd ____________________________________ *** our email address has changed! info@pepmeierengines.com pepmeierengines.com Friend us on Facebook too: www.facebook.com/profile.php?id=100011443683384 Pepmeier Engine Development |
|
|
|
06-14-2020
|
#2 |
 
Join Date: Apr 2007
Location: Northern VA
Posts: 2,658
|
Re: RH oem harness routing
The harness run down behind the right cylinder head. The O2 wiring splits off as seen here
IMG_0847.JPG IMG_0846.JPG The remaining harness runs forward connecting to the oil level and crank sensors. IMG_0842.JPG IMG_0843.JPG Sent from my iPhone using ZR-1 Net Registry
__________________
Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake |
|
|
|
|
06-14-2020
|
#3 |
 
Join Date: Aug 2012
Location: Ellicott City, MD
Posts: 1,704
|
Re: RH oem harness routing
That gentlemen is a better than new engine and clean engine bay!
__________________
Charlie __________ Dredgeguy WAZOO Member 1992 Bright Red/Black ZR1 #246 Dana 4:10 gears Polished LT5 by Haibeck Polished Fikse FM5's with Michelin Pilot Sport 2 Stainless Works headers and cats with Corsa |
|
|
|
|
06-14-2020
|
#4 |
 
Join Date: Dec 2003
Location: Arcadia,OK
Posts: 3,393
|
Re: RH oem harness routing
Yes, that's what I was thinking. You want to come and spend the summer with me Phil? Shop is air conditioned & plenty for you to do if you were so inclined.
__________________
Jerry Downey JERRYS LT5 GASKETS & PARTS http://www.jerrysgaskets.com 1994 ZR-1, Black/Black, Lingenfelter Aerobody, 416cu in, 3.91 gears, coil-over susp, Brembo brakes, etc. 2016 Black-Red, 3LT-Z51 Auto 8-speed. |
|
|
|
|
06-15-2020
|
#5 |
|
Join Date: May 2007
Location: Chicagoland, IL
Posts: 9,704
|
Re: RH oem harness routing
Seriously Phil. Does that motor even have any fluids in it? 🤣🤣😉
__________________
[SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX |
|
|
|
|
06-15-2020
|
#6 |
|
Join Date: Aug 2005
Location: Fishers, IN
Posts: 814
|
Re: RH oem harness routing
Phil for the win. Thanks, man.
__________________
Todd ____________________________________ *** our email address has changed! info@pepmeierengines.com pepmeierengines.com Friend us on Facebook too: www.facebook.com/profile.php?id=100011443683384 Pepmeier Engine Development |
|
|
|
|
06-15-2020
|
#7 | |
|
Join Date: Apr 2007
Location: Northern VA
Posts: 2,658
|
Re: RH oem harness routing
Quote:
__________________
Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake |
|
|
|
|
 |
|
|
Linear Mode
