![]() |
#1 |
![]() Join Date: Jul 2016
Location: Greater St. Louis
Posts: 487
|
![]()
Hi there. Are the door belt line moldings longer on the ZR-1, or same part # as the base car?
|
![]() |
![]() |
![]() |
#2 |
![]() Join Date: Aug 2012
Location: Ellicott City, MD
Posts: 1,676
|
![]()
I know the short piece is longer on the Z
__________________
Charlie __________ Dredgeguy WAZOO Member 1992 Bright Red/Black ZR1 #246 Dana 4:10 gears Polished LT5 by Haibeck Polished Fikse FM5's with Michelin Pilot Sport 2 Stainless Works headers and cats with Corsa |
![]() |
![]() |
![]() |
#3 |
![]() Join Date: Jul 2016
Location: Greater St. Louis
Posts: 487
|
![]()
You’re right. I should spec I’m asking about the molding on the door.
|
![]() |
![]() |
![]() |
#4 |
![]() Join Date: Oct 2017
Location: TX
Posts: 2,000
|
![]()
I have been told they are the same. Might check with Mark @ Mirrock. He will know for sure.
![]()
__________________
Kenny 1990 #442 ![]() |
![]() |
![]() |
![]() |
#5 | |
![]() ![]() Join Date: Nov 2007
Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri
Posts: 6,493
|
![]() Quote:
![]()
__________________
Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry |
|
![]() |
![]() |
![]() |
#6 |
Join Date: Dec 2007
Location: Fremont,Ca
Posts: 3,058
|
![]()
They are the same part on a 91-95,I know this for fact. I wanted to repaint the door trim on my 91,I thought that other than the threaded stud at each end the center of the trim had snaps,wrong. On the early 91s,at least up to VIN 634,the trim has threaded studs the length of the trim,I destroyed one piece getting it off. I’m looking for a driver door piece with all threaded studs if anybody happens to have one.
|
![]() |
![]() |
![]() |
#7 |
![]() Join Date: Jul 2016
Location: Greater St. Louis
Posts: 487
|
![]()
Appreciate the responses.
|
![]() |
![]() |
![]() |
#8 |
Join Date: Dec 2007
Location: Fremont,Ca
Posts: 3,058
|
![]()
I forgot to add,THE ENTIRE DOOR HAD TO COME APART TO GET TO ALL THE NUTS! That was one of the situations that if you ever got the chance to meet the engineer that designed that part,you'd slap em.
|
![]() |
![]() |
![]() |
#9 |
![]() Join Date: May 2010
Location: Japan
Posts: 3,573
|
![]()
The door molding is same for 90. I have them NOS and checked the part numbers. Only the dog leg (or whatever that piece is behind the door is) and rear bumpers have different molding than a standard C4.
Sent from my iPhone using ZR-1 Net Registry
__________________
Craig "ZR-1 NO KA 'OI" "ZR-1 ICHIBAN" 1995 #228 Black/Black with Dunn Heads ZR-1 owner since September 2003 ZR-1 Net Registry Founding Member #0074 NCM Lifetime Member #2048 ![]() |
![]() |
![]() |
![]() |
|
|