LED hedlamp install - ZR-1 Net Registry Forums

XfireZ51 · 11-15-2018

I recently bought a set of OSRAM LED headlamps. In process of installing them, and I notice that on the headlamp buckets for my ZR, there are only 2 adjusters,
One vertical, one horizontal. However, the FSM shows 3. But the bucket has provision for only 2 so it appears that it is not a case of missing parts or anything like that. It looks stock.

Paul Workman · 11-15-2018

Dom,

Did you opt for LOAD RESISTORS, or clip/ground the FOG LIGHT RELAY?

Flyman 27 · 11-15-2018

Where did you end up getting the headlights?

XfireZ51 · 11-15-2018

Quote:

Originally Posted by Paul Workman

Dom,

Did you opt for LOAD RESISTORS, or clip/ground the FOG LIGHT RELAY?

I’m going to connect a separate ground. The horn ground is very close to the fogs.

Wayne,

I got these off Amazon.Mistakenly, I ended up w another set also. Once I get these hooked up and tested I may sell the other set.

XfireZ51 · 11-15-2018

Paul,

Just realized I can’t do it that way. Hate idea of clipping wires.

Jagdpanzer · 11-15-2018

Take a look at the way brother Yun (secondchance) solved this issue with a relay terminal jumper.
He laid hands on my Z when when I switched over to GE LEDs as couple years back and all is well with the fog lamps.

dredgeguy · 11-15-2018

Did mine as well but recall we cut a wire and then grounded it. All is well with fog lights.

secondchance · 11-15-2018

First two Zs - mine and dregeguy's - I located fog light ground wire (light green, I think), cut and grounded. Third Z, Phil's, I pulled the fog light relay, bent the ground leg, soldered about 8-10" long wire and grounded it. Both methods worked fine. The latter, relay leg mod, avoided cutting any factory wiring.

XfireZ51 · 11-15-2018

Quote:

Originally Posted by secondchance

First two Zs - mine and dregeguy's - I located fog light ground wire (light green, I think), cut and grounded. Third Z, Phil's, I pulled the fog light relay, bent the ground leg, soldered about 8-10" long wire and grounded it. Both methods worked fine. The latter, relay leg mod, avoided cutting any factory wiring.

Yun,

Are u saying you grounded the fog lamp at the front of the engine compartment?

secondchance · 11-16-2018

Quote:

Originally Posted by XfireZ51

Yun,

Are u saying you grounded the fog lamp at the front of the engine compartment?

least intrusive method I found is to remove fog lamp relay under the passenger side dash, bend the grounding leg sideway and up (so that ground circuit is defeated), solder a wire on the ground leg and finally ground this new wire by hooping it under a 10 mm nut close to bottom of passenger side A pillar/front edge of passenger side door.
Soldering on to relay leg is pretty easy because most, if not all, relay legs have a hole where you can thread a wire before soldering.

11-15-2018	#1
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,708	LED hedlamp install I recently bought a set of OSRAM LED headlamps. In process of installing them, and I notice that on the headlamp buckets for my ZR, there are only 2 adjusters, One vertical, one horizontal. However, the FSM shows 3. But the bucket has provision for only 2 so it appears that it is not a case of missing parts or anything like that. It looks stock. __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX Last edited by XfireZ51; 03-08-2024 at 03:09 PM.

11-15-2018	#2
Paul Workman Join Date: Nov 2007 Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri Posts: 6,493	Re: LED hedlamp install Dom, Did you opt for LOAD RESISTORS, or clip/ground the FOG LIGHT RELAY? __________________ Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry

11-15-2018	#3
Flyman 27 Join Date: Apr 2017 Location: Wayne Illinois Posts: 402	Re: LED hedlamp install Where did you end up getting the headlights? __________________ 91-#1935 Black/black & gray, Haibeck 500 Cams by Pete

11-15-2018	#5
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,708	Re: LED hedlamp install Paul, Just realized I can’t do it that way. Hate idea of clipping wires. __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX

11-15-2018	#6
Jagdpanzer Join Date: Apr 2007 Location: Northern VA Posts: 2,661	Re: LED hedlamp install Take a look at the way brother Yun (secondchance) solved this issue with a relay terminal jumper. He laid hands on my Z when when I switched over to GE LEDs as couple years back and all is well with the fog lamps. __________________ Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake

11-15-2018	#7
dredgeguy Join Date: Aug 2012 Location: Ellicott City, MD Posts: 1,713	Re: LED hedlamp install Did mine as well but recall we cut a wire and then grounded it. All is well with fog lights. __________________ Charlie __________ Dredgeguy WAZOO Member 1992 Bright Red/Black ZR1 #246 Dana 4:10 gears Polished LT5 by Haibeck Polished Fikse FM5's with Michelin Pilot Sport 2 Stainless Works headers and cats with Corsa

11-15-2018	#8
secondchance Join Date: Aug 2006 Location: McLean, VA Posts: 3,723	Re: LED hedlamp install First two Zs - mine and dregeguy's - I located fog light ground wire (light green, I think), cut and grounded. Third Z, Phil's, I pulled the fog light relay, bent the ground leg, soldered about 8-10" long wire and grounded it. Both methods worked fine. The latter, relay leg mod, avoided cutting any factory wiring.