|
08-25-2021
|
#1 |
 
Join Date: Jan 2020
Location: conroe, tx
Posts: 87
|
Another dumb question of the day
back in march my clutch slave started to leave a puddle on the floor and i had to pump the clutch to get a full peddle every time i would go to start it after it had set all night. the slave and the master looked to be the original from the factory so i pulled them out and sent them to the zfdoc to get rebuilt. eventually, for other reasons, i ended up pulling the engine and transmission and the front cradle and now i am in the process of putting everything in its place. now, 5-6 months later, i have a relay that i cannot figure out where it attaches to on the car. it comes out of the loom in front of the brake booster and has about 12" of wire so i have scoured everywhere on the firewall, the frame and the lower rear wheel house looking for 2 screw holes that matches the bracket.
am i blind? anyway, i am in need of an extra set of eyes to place this relay in it's correct location. thanks all. |
|
|
|
08-25-2021
|
#2 |
 
Join Date: Nov 2007
Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri
Posts: 6,493
|
Re: Another dumb question of the day
Just a guess... But, installing a relay in that area to relieve the current load (a DIY upgrade for the 90-92 ZR-1s) might be what that is. A photo would help!
(See Cliff's STICKY notes regarding that relay. There is about a foot or so purple wire from the relay that passes under the plenum to the starter - IF that is the relay you're dealing with)
__________________
Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry |
|
|
|
|
08-25-2021
|
#3 |
|
Join Date: Jan 2020
Location: conroe, tx
Posts: 87
|
Re: Another dumb question of the day
sorry...forgot to include the photo.
google identifies this part number, 14089936, as a fuel pump relay |
|
|
|
|
08-25-2021
|
#4 |
Join Date: Jan 2006
Location: Decatur, AL
Posts: 1,119
|
Re: Another dumb question of the day
It goes in the drivers rear wheel well liner. I think it may have had two push pins but just going off memory.
__________________
Corvette95 Registry and Forum (*************) 1989 C4 Conv Wht/Gry Auto Hardtop Top Flight SOLD 1995 C4 Coupe Purple/Blk 6 Speed 1989 C4 Conv Wht/Red Auto SOLD 1996 C4 Conv Black/Tan Auto SOLD 1994 C4 Coupe Wht/Blk SOLD 1995 C4 ZR-1 White/Gry #278 Dual Dunn Head SOLD 1986 C4 Coupe Black/Red 4+3 SOLD 1990 C4 ZR-1 Red/Red #0454 |
|
|
|
|
08-25-2021
|
#5 |
|
Join Date: Jan 2020
Location: conroe, tx
Posts: 87
|
Re: Another dumb question of the day
wvzr-1 responded to my thread on that other forum and id'd it as the 1-4 upshift relay and i confirmed it with the fsm. only the center hole attaches it to the frame and the attaching hole is almost under the down bar.
one more set of eyes usually settles the problem. now i can move back over to the other side of the engine. |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
