Rebuilt tranny and found rear spring issues - ZR-1 Net Registry Forums

JSad · 11-01-2020

When I bought my white 1991 ZR-1 #210 a couple years ago it was a rescue of a pretty abused car. It was running and drivable when I bought it but needs much TLC. I am slowly getting it back into shape. Engine work is done (stock) and I have completed some other miscellaneous issues. One of the problems was the syncros 1st to 2nd.

I just had the transmission rebuilt by the local shop I use, Pinnacle Performance. They did a fantastic job on the rebuild and I had them do the rear main seal, new clutch, fidenza flywheel, add ZF Docs short shifter and beam plates, then replaced the resonator with an x-pipe and added Haibeck's chip.

Love the results...but...as I was crawling around underneath admiring the work, I noticed my rear spring is cracked and delaminating. So, next project is to replace it. My questions are, does someone offer a "kit" with everything I need, and what else should/could I do while replacing it?

Z51JEFF · 11-01-2020

I'd just look for a nice used part, it sure you can buy a new one.

Hib Halverson · 11-08-2020

You need a rear spring and the one you want will be labeled and likely stamped with the spring code: NYR.

At this point in time, it's unlikely, but not impossible, that you're going to find a new spring. Looking for a good used part is what you may end-up doing.

There are a lot of NYR springs out there because it fits:

85-93 base coupes
89-90 coupes w FE7 and FX3
90-91 ZR1

Good luck!

JSad · 11-08-2020

What's your thoughts on the composite replacement sprongs, like those from Ecklers or similar?

11-01-2020	#1
JSad Join Date: Aug 2018 Location: Tulsa Posts: 43	Rebuilt tranny and found rear spring issues When I bought my white 1991 ZR-1 #210 a couple years ago it was a rescue of a pretty abused car. It was running and drivable when I bought it but needs much TLC. I am slowly getting it back into shape. Engine work is done (stock) and I have completed some other miscellaneous issues. One of the problems was the syncros 1st to 2nd. I just had the transmission rebuilt by the local shop I use, Pinnacle Performance. They did a fantastic job on the rebuild and I had them do the rear main seal, new clutch, fidenza flywheel, add ZF Docs short shifter and beam plates, then replaced the resonator with an x-pipe and added Haibeck's chip. Love the results...but...as I was crawling around underneath admiring the work, I noticed my rear spring is cracked and delaminating. So, next project is to replace it. My questions are, does someone offer a "kit" with everything I need, and what else should/could I do while replacing it?

11-08-2020	#3
Hib Halverson Join Date: Jun 2005 Location: CenCoast California Posts: 899	Re: Rebuilt tranny and found rear spring issues You need a rear spring and the one you want will be labeled and likely stamped with the spring code: NYR. At this point in time, it's unlikely, but not impossible, that you're going to find a new spring. Looking for a good used part is what you may end-up doing. There are a lot of NYR springs out there because it fits: 85-93 base coupes 89-90 coupes w FE7 and FX3 90-91 ZR1 Good luck! __________________ Hib Halverson Technical Writer former owner 95 VIN 0140 current owner 19 VIN 1878

11-08-2020	#4
JSad Join Date: Aug 2018 Location: Tulsa Posts: 43	Re: Rebuilt tranny and found rear spring issues What's your thoughts on the composite replacement sprongs, like those from Ecklers or similar?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-01-2020	#2
Z51JEFF Join Date: Dec 2007 Location: Fremont,Ca Posts: 3,078	Re: Rebuilt tranny and found rear spring issues I'd just look for a nice used part, it sure you can buy a new one.