Thermostats Issue - ZR-1 Net Registry Forums

Ccmano · 06-26-2018

Ok... this is getting frustrating. Take a look at the photo below. The thermostat on the left is what came out of the car and is correct. Note the brass piece on the bottom with the two cut outs.

The middle one is an AC/Delco that came from RockAuto. Note the bottom piece, in this case steel and no cutouts. To my knowledge not correct.

On the left, also from RockAuto, is a Gates brand. Note the bottom cup shaped piece. Also not correct. This is the second one like this is have received like this, the previous one in a Stant box marked 14068. I should also add the Gates listing on RockAuto showed a photo of the correct thermostat like the one on the left. What I got looks nothing like it.

Does anyone know if the AC/Delco shown is usable? Does anyone have a source for a correct thermostat? (that doesn’t cost stupid money)

Looking at the one that came out it’s apparent that it’s not the at old. I say that because someone drilled a 1/8th hole, per Jerry’s writeup, in the top plate, indicating a relatively recent replacement. I may just check it for proper opening and put it back in.

On a side note when I opened the thermostat housing on the new (to me) engine I found an L98 thermostat.

H

Dynomite · 06-26-2018

Quote:

Originally Posted by Ccmano

Ok... this is getting frustrating. Take a look at the photo below. The thermostat on the left is what came out of the car and is correct. Note the brass piece on the bottom with the two cut outs.

Does anyone have a source for a correct thermostat? (that doesn’t cost stupid money)

Looking at the one that came out it’s apparent that it’s not the at old. I say that because someone drilled a 1/8th hole, per Jerry’s writeup, in the top plate, indicating a relatively recent replacement. I may just check it for proper opening and put it back in.

You can get the Stant 180 deg Thermostat 14068 from Marc Haibeck.

I am trying These guys just because...… Stant 14068 Thermostat

Do not use the two on the right and there is no need for the 1/8 inch hole in the flange. If you test the thermostat on the left it should open a bit before 180 deg F and be fully open at bit over 180 deg F.
I would just use the Stant 14068 on the left if it opens at around 180 deg F as the 1/8 inch hole will not have much effect on function of the thermostat and that thermostat looks almost new.

See …….. Thermostats, Fans, Radiators and Coolant Filling

Ccmano · 06-26-2018

You saw what I got when I ordered a Stant 14068, good luck.

I don’t see anything listed on Marc’s site that he is selling thermostats.
H

Dynomite · 06-26-2018

Quote:

Originally Posted by Ccmano

You saw what I got when I ordered a Stant 14068, good luck.

I don’t see anything listed on Marc’s site that he is selling thermostats.
H

Text Message Marc and I think he will sell you the correct 180 deg F Stant 14068.

But...…..
I would just use the Stant 14068 on the left if it opens at around 180 deg F as the 1/8 inch hole will not have much effect on function of the thermostat and that thermostat looks almost new.

XfireZ51 · 06-27-2018

Hans,

I’m using correct thermo from Jerry’s but w 2 holes drilled. Works fine so I wouldn’t sweat the hole in the thermo. And yes u want a 180* thermo for Closed Loop.

Ccmano · 06-27-2018

The hole is not an issue. I used two holes drilled out on the last car. It worked well for the hot California climate where I lived at the time. I just want to be able to order and receive the correct thermostat. I’ll give Marc a call today. In the mean time I’m putting the correct one I have back in, May even add a second hole.
H

rush91 · 06-27-2018

I believe I got mine from Jerry's a year ago. I never drilled any holes, and never have had any issues since install.

Ccmano · 06-27-2018

Unfortunately Jerrys is out of stock.
H

Sent from my iPhone using ZR-1 Net Registry

XfireZ51 · 06-27-2018

Hans,

I may have one of my previous ones before I installed the Fluidyne rad.

Dynomite · 06-28-2018

Quote:

Originally Posted by Ccmano

You saw what I got when I ordered a Stant 14068, good luck.

$24......Shows a gasket but came without a gasket....Price was right

Stant 14068 Thermostat

Jerry has the Rubber gasket

Stant 14068 gasket

06-26-2018	#1
Ccmano Join Date: Jun 2006 Location: Sparks, NV Posts: 2,852	Thermostats Issue Ok... this is getting frustrating. Take a look at the photo below. The thermostat on the left is what came out of the car and is correct. Note the brass piece on the bottom with the two cut outs. The middle one is an AC/Delco that came from RockAuto. Note the bottom piece, in this case steel and no cutouts. To my knowledge not correct. On the left, also from RockAuto, is a Gates brand. Note the bottom cup shaped piece. Also not correct. This is the second one like this is have received like this, the previous one in a Stant box marked 14068. I should also add the Gates listing on RockAuto showed a photo of the correct thermostat like the one on the left. What I got looks nothing like it. Does anyone know if the AC/Delco shown is usable? Does anyone have a source for a correct thermostat? (that doesn’t cost stupid money) Looking at the one that came out it’s apparent that it’s not the at old. I say that because someone drilled a 1/8th hole, per Jerry’s writeup, in the top plate, indicating a relatively recent replacement. I may just check it for proper opening and put it back in. On a side note when I opened the thermostat housing on the new (to me) engine I found an L98 thermostat. H __________________ 90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold. Last edited by Ccmano; 03-29-2020 at 07:43 PM.

06-26-2018	#3
Ccmano Join Date: Jun 2006 Location: Sparks, NV Posts: 2,852	Re: Thermostats Issue You saw what I got when I ordered a Stant 14068, good luck. I don’t see anything listed on Marc’s site that he is selling thermostats. H __________________ 90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold. Last edited by Ccmano; 06-26-2018 at 11:40 PM.

06-27-2018	#5
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,708	Re: Thermostats Issue Hans, I’m using correct thermo from Jerry’s but w 2 holes drilled. Works fine so I wouldn’t sweat the hole in the thermo. And yes u want a 180* thermo for Closed Loop. __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX

06-27-2018	#6
Ccmano Join Date: Jun 2006 Location: Sparks, NV Posts: 2,852	Re: Thermostats Issue The hole is not an issue. I used two holes drilled out on the last car. It worked well for the hot California climate where I lived at the time. I just want to be able to order and receive the correct thermostat. I’ll give Marc a call today. In the mean time I’m putting the correct one I have back in, May even add a second hole. H __________________ 90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold.

06-27-2018	#7
rush91 Join Date: Feb 2016 Location: Carterville Illinois Posts: 852	Re: Thermostats Issue I believe I got mine from Jerry's a year ago. I never drilled any holes, and never have had any issues since install.

06-27-2018	#8
Ccmano Join Date: Jun 2006 Location: Sparks, NV Posts: 2,852	Re: Thermostats Issue Unfortunately Jerrys is out of stock. H Sent from my iPhone using ZR-1 Net Registry __________________ 90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold.

06-27-2018	#9
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,708	Re: Thermostats Issue Hans, I may have one of my previous ones before I installed the Fluidyne rad. __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode