|
06-26-2017
|
#1 |
 
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,156
|
need hood side emblem help
What is the correct distances for the side emblem on the hood:
- Bottom of hood to bottom of emblem - Door side of hood to door side of emblem. My hood has no holes and the emblems don't have the alignment pins decided to not do the splash ZR-1 stickers on the hood. I have something else
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
06-26-2017
|
#2 |
 
Join Date: Feb 2012
Location: Ledyard,CT
Posts: 8,301
|
Re: need hood side emblem help
1990 ZR-1 only had the badge on the rear bumper!
|
|
|
|
|
06-26-2017
|
#3 | |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,156
|
Re: need hood side emblem help
Quote:
Yeah I know. What is your point? Sent from my iPhone using ZR-1 Net Registry
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
|
|
06-26-2017
|
#4 | |
|
Join Date: Feb 2016
Location: Carterville Illinois
Posts: 854
|
Re: need hood side emblem help
Quote:
Indeed! As do the 1991 models, but GM corrected that mistake on the 92's and up.... I've had several people say nice Vette, but then they notice the ZR-1 side badges on the hood, and it turns into oh wow!! I think they add a beautiful touch to ours Z's |
|
|
|
|
|
06-26-2017
|
#5 |
|
Join Date: Feb 2012
Location: Ledyard,CT
Posts: 8,301
|
Re: need hood side emblem help
My 95 only has the badge on the rear bumper!
|
|
|
|
|
06-26-2017
|
#6 |
|
Join Date: Feb 2016
Location: Carterville Illinois
Posts: 854
|
Re: need hood side emblem help
|
|
|
|
|
06-26-2017
|
#7 |
Join Date: Nov 2007
Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri
Posts: 6,466
|
Re: need hood side emblem help
Ami's is
5-1/4" from the edge of the of the clamshell to the rear most edge of the badge, and - 1-1/4" up from the bottom edge of the clamshell to the bottom edge of the ZR-1 portion of the badge. This places the center of the badge over the center line, perpendicular to the gills in the gill panel below. Looks VERY nice (the badges). Her's is a 91, and I assumed they were factory installed. Perhaps not, from what I'm hearing. But, they look like they SHOULD have been there if they weren't! I've been considering putting them on my 90 BECAUSE I believe we should make the point that we exist. If I could find some red ones somewhere, I'd be hard pressed not to install them - even tho I'm basically a purist - at least where it shows! 
|
|
|
|
|
06-26-2017
|
#8 |
Join Date: Dec 2007
Location: Fremont, CA
Posts: 3,087
|
Re: need hood side emblem help
I have the specs,just need to find them. At the very least I'll measure mine on the car. I do remember 5-1/2 and 2-1/4 but it's been awhile.
|
|
|
|
|
06-26-2017
|
#9 |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,156
|
Re: need hood side emblem help
Paul I have 3 brand new red ones.. I am not putting ZR-1 on the hood.. i have something else in mind
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
|
06-27-2017
|
#10 |
|
Join Date: Dec 2007
Location: Fremont, CA
Posts: 3,087
|
Re: need hood side emblem help
You ever get the measurements you were looking for? I've got from the back edge of the hood to the edge of the emblem is 5-1/2 and bottom edge of hood is 2-1/4 to bottom bottom edge of emblem.
|
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
