Motor Mount Replacement - ZR-1 Net Registry Forums

KJL · 11-11-2016

Because of the heat shields, it is very difficult to tell what condition they are in. That said, they are 27 years old and figured I would just replace them before they are no longer available. How is this done? I already have the car up in the air on jack stands fixing a bunch of other stuff and have the exhaust removed from the headers and the c-beam and propeller shaft are also removed.

5ABI VT · 11-11-2016

Interested to know as well. Does anyone make solid mounts ?

Jagdpanzer · 11-11-2016

GM part #10157980

A26B · 11-15-2016

Here's a link with the procedure for replacing the Motor Mounts.
http://www.jerrysgaskets.com/mount-motor-used-90-95-3c/

See description for Mtr Mount at that link.

Sent from my iPhone using ZR-1 Net Registry

KJL · 11-15-2016

Thanks for the input, I was hoping the headers would not have to be removed. From what I can tell they look to be in good shape. No signs of leakage. I think I will leave them be for now.

11-11-2016	#2
5ABI VT Join Date: Jun 2013 Location: Toronto Posts: 781	Re: Motor Mount Replacement Interested to know as well. Does anyone make solid mounts ?

11-11-2016	#3
Jagdpanzer Join Date: Apr 2007 Location: Northern VA Posts: 2,662	Re: Motor Mount Replacement GM part #10157980 __________________ Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake

11-15-2016	#4
A26B Join Date: Dec 2003 Location: Arcadia,OK Posts: 3,396	Motor Mount Replacement Here's a link with the procedure for replacing the Motor Mounts. http://www.jerrysgaskets.com/mount-motor-used-90-95-3c/ See description for Mtr Mount at that link. Sent from my iPhone using ZR-1 Net Registry __________________ Jerry Downey JERRYS LT5 GASKETS & PARTS http://www.jerrysgaskets.com 1994 *ZR-1, Black/Black, Lingenfelter Aerobody, 416cu in, 3.91 gears, coil-over susp, Brembo brakes, etc. 2016 Black-Red, 3LT-Z51 Auto 8-speed. Last edited by A26B; 11-15-2016 at 07:40 PM.*

11-15-2016	#5
KJL Join Date: Mar 2013 Location: Roswell, GA Posts: 234	Re: Motor Mount Replacement Thanks for the input, I was hoping the headers would not have to be removed. From what I can tell they look to be in good shape. No signs of leakage. I think I will leave them be for now. __________________ 1995 ZR1 #159 Ported,Corsa,4.10 Rear, Dual Disc RAM Clutch, Alum Flywheel, Haibeck Chip, ZFDoc Plates, Relocated Battery 400 rwhp 1992 ZR1 #280 Ported, Locked Secondary's, Flowmaster Exhaust, Haibeck Chip, 375rwhp 1996 Collectors LT4 (Stock) 1972 Convertible 434 Small Block 572 rwhp

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-11-2016	#1
KJL Join Date: Mar 2013 Location: Roswell, GA Posts: 234	Motor Mount Replacement Because of the heat shields, it is very difficult to tell what condition they are in. That said, they are 27 years old and figured I would just replace them before they are no longer available. How is this done? I already have the car up in the air on jack stands fixing a bunch of other stuff and have the exhaust removed from the headers and the c-beam and propeller shaft are also removed. __________________ 1995 ZR1 #159 Ported,Corsa,4.10 Rear, Dual Disc RAM Clutch, Alum Flywheel, Haibeck Chip, ZFDoc Plates, Relocated Battery 400 rwhp 1992 ZR1 #280 Ported, Locked Secondary's, Flowmaster Exhaust, Haibeck Chip, 375rwhp 1996 Collectors LT4 (Stock) 1972 Convertible 434 Small Block 572 rwhp