Got Lucky tonite - ZR-1 Net Registry Forums

Bearly Flying · 11-02-2013

No, Not that Lucky..... Settle down.

Finally got some time off and started reassembling my 91 from repairing my starter solenoid this spring.

Got the Inj Housings torqued down, installed the new Fuel Injectors and rails, was installing the retaining clips on the Fuel Inj to rails.

Last one going on, #8 secondary when my fat fingers fumbled and away it went down into the bowels of the motor.

#@^%&**^$, started looking around with the trouble light, I could just see the edge of it down alongside the starter.

Out with my trusty long handled forceps, Ahah,,,,,, I managed to push it completely under the starter. $%^&#$%@,,,, So out with a piece of wire, twist and bend it,,,, go fishing in the dark.... No Joy.....

Son ofa Biatch,,, Don't tell me I'm going to have to strip everything to get the freaking starter out again....

Sit down, have a smoke, Figured I would be making a trip to the Chev Dealer tomorrow, should be a common part, but what are the chances of being in stock???? Probably not good, with My luck.

Go to get up and notice my long handled blow gun on the bench, Hmmmm..... Managed to get the head of the blow gun down the hole in front of the starter where the secondary vacuum switch used to reside.

Couple of really good blast of air and I heard a light metal sounding thing ricocheting around the engine and then the sound of it hitting the concrete on the floor.... Success.

OK, where did the little bugger go now? A few minutes crawling around looking under everything found it snuggled up against the inside of a tire.

CAREFULLY installed it this time.

Enough for tonite, mixing a cocktail.....

XfireZ51 · 11-02-2013

Thank heaven for small miracles.

Paul Workman · 11-02-2013

I hear ya. You got lucky!

I lost a 6" long ratchet handle for my 1/4" drive socket set - slipped out of my hand and disappeared between the tunnel and the bell housing while attempting to tighten the DIS connector at the back of the motor. It never hit the floor, but in spite of me climbing under to look, use a loop of string to swipe the top of the bell housing, a couple hours round and round again in all...I never found it! It just vaporized!

And, a black hole for long tube header bolts is the pocket formed by the four pipes where they join the collector section. (ask me how I know!

)

XfireZ51 · 11-02-2013

Don't you just hate it when a small bolt or socket falls into the valley and

a) you just finished bolting the plenum down

b) it finds its way under the starter

WARP TEN · 11-02-2013

Don't you love life's little victories!!! -Bob

GOLDCYLON · 11-02-2013

Quote:

Originally Posted by Bearly Flying

No, Not that Lucky..... Settle down.

Finally got some time off and started reassembling my 91 from repairing my starter solenoid this spring.

Got the Inj Housings torqued down, installed the new Fuel Injectors and rails, was installing the retaining clips on the Fuel Inj to rails.

Last one going on, #8 secondary when my fat fingers fumbled and away it went down into the bowels of the motor.

#@^%&**^$, started looking around with the trouble light, I could just see the edge of it down alongside the starter.

Out with my trusty long handled forceps, Ahah,,,,,, I managed to push it completely under the starter. $%^&#$%@,,,, So out with a piece of wire, twist and bend it,,,, go fishing in the dark.... No Joy.....

Son ofa Biatch,,, Don't tell me I'm going to have to strip everything to get the freaking starter out again....

Sit down, have a smoke, Figured I would be making a trip to the Chev Dealer tomorrow, should be a common part, but what are the chances of being in stock???? Probably not good, with My luck.

Go to get up and notice my long handled blow gun on the bench, Hmmmm..... Managed to get the head of the blow gun down the hole in front of the starter where the secondary vacuum switch used to reside.

Couple of really good blast of air and I heard a light metal sounding thing ricocheting around the engine and then the sound of it hitting the concrete on the floor.... Success.

OK, where did the little bugger go now? A few minutes crawling around looking under everything found it snuggled up against the inside of a tire.

CAREFULLY installed it this time.

Enough for tonite, mixing a cocktail.....

Well that's thinking outside the box....

And we have all done and said the same chant. Dammit dammit dammit lol. Enjoy that cocktail you earned it.

Schrade · 11-02-2013

Simple Murphy's Law geometric principle for finding stuff - that actually DOES make it to the floor...

Draw a line from front right tire to rear left tire, and from front left to rear right. Where they intersect, 'X' marks the spot

XfireZ51 · 11-02-2013

I keep an articulated extending magnet w an LED light built into the head. Perfect for this type of search and rescue mission.

Bearly Flying · 11-02-2013

"articulated extending magnet w an LED light built into the head."

Now that sounds like a useful tool, where did you find it?

LGAFF · 11-02-2013

Stop messing around and get that thing fired up!!!

11-02-2013	#1
Bearly Flying Join Date: Dec 2012 Location: Ponoka, Alberta, Canada Posts: 158	Got Lucky tonite No, Not that Lucky..... Settle down. Finally got some time off and started reassembling my 91 from repairing my starter solenoid this spring. Got the Inj Housings torqued down, installed the new Fuel Injectors and rails, was installing the retaining clips on the Fuel Inj to rails. Last one going on, #8 secondary when my fat fingers fumbled and away it went down into the bowels of the motor. #@^%&**^$, started looking around with the trouble light, I could just see the edge of it down alongside the starter. Out with my trusty long handled forceps, Ahah,,,,,, I managed to push it completely under the starter. $%^&#$%@,,,, So out with a piece of wire, twist and bend it,,,, go fishing in the dark.... No Joy..... Son ofa Biatch,,, Don't tell me I'm going to have to strip everything to get the freaking starter out again.... Sit down, have a smoke, Figured I would be making a trip to the Chev Dealer tomorrow, should be a common part, but what are the chances of being in stock???? Probably not good, with My luck. Go to get up and notice my long handled blow gun on the bench, Hmmmm..... Managed to get the head of the blow gun down the hole in front of the starter where the secondary vacuum switch used to reside. Couple of really good blast of air and I heard a light metal sounding thing ricocheting around the engine and then the sound of it hitting the concrete on the floor.... Success. OK, where did the little bugger go now? A few minutes crawling around looking under everything found it snuggled up against the inside of a tire. CAREFULLY installed it this time. Enough for tonite, mixing a cocktail..... __________________ 91 ZR-1 Arctic White/Gray 01 C-5 Magnetic Red/Black 85 FJ 1100 (Big Bore kit, Hooligan Bike) 05 FJR 1300 Yamaha (Long Distance, Sport Touring) And a whole whack of RC Planes

11-02-2013	#2
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,708	Re: Got Lucky tonite Thank heaven for small miracles. __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX

11-02-2013	#3
Paul Workman Join Date: Nov 2007 Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri Posts: 6,493	Re: Got Lucky tonite I hear ya. You got lucky! I lost a 6" long ratchet handle for my 1/4" drive socket set - slipped out of my hand and disappeared between the tunnel and the bell housing while attempting to tighten the DIS connector at the back of the motor. It never hit the floor, but in spite of me climbing under to look, use a loop of string to swipe the top of the bell housing, a couple hours round and round again in all...I never found it! It just vaporized! And, a black hole for long tube header bolts is the pocket formed by the four pipes where they join the collector section. (ask me how I know!) __________________ Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry

11-02-2013	#4
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,708	Re: Got Lucky tonite Don't you just hate it when a small bolt or socket falls into the valley and a) you just finished bolting the plenum down b) it finds its way under the starter __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX

11-02-2013	#5
WARP TEN Join Date: Apr 2007 Location: Lake Bluff, IL Posts: 2,094	Re: Got Lucky tonite Don't you love life's little victories!!! -Bob __________________ 2016 Long Beach Red Z06 #10281 "POPS Z" 1995 Polo Green #409 "WARP TEN"--Haibeck 350/510 package, 4.10s, Hurst, Stock Exhaust with QTP Cutouts --Sold but still running strong 1993 Quasar Blue #161 "HIL KING" --Sold but still running strong, now with more than 120,000 miles 1967 Marlboro Maroon/Saddle Corvette Coupe 300 hp/4-spd --Sold a long time ago ZR-1 Net Registry Founding Member #95 NCM Lifetime Member Favorite Quote--Attributed to Mickey Thompson: "Too Much Horsepower is Almost Enough"

11-02-2013	#7
Schrade Join Date: Dec 2012 Location: NC Posts: 1,786	Re: Got Lucky tonite Simple Murphy's Law geometric principle for finding stuff - that actually DOES make it to the floor... Draw a line from front right tire to rear left tire, and from front left to rear right. Where they intersect, 'X' marks the spot __________________ I'm getting my snappics / threads removed blindly as fast as I can, to get in compliance with copyright / license TOS on the boards here (lots of FSM pages and other copyright / license violations on my part; sorry guys). And thanks to all the guys who didn't whine when I posted those FSM copyrighted / licensed stuff in my threads... ( :thumbsup: [b]and to think I complied with a mod's request to delete a pic of him in a Challenge Car in NCM Museum, so he wouldn't get in hot water)[/b] Thanks to several guys here for sending parts FREE; BearlyFlying, WeGone, Geezer, GoldCylon, and more there, TonyD, mike100, fletchusmc... 1990 #2794; 4L60e Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless, Power Effects 3" [IMG]https://lh5.googleusercontent.com/-GHpfzty7DVU/UQn-0Ru2xAI/AAAAAAAAA14/08mz1p4QLD4/s445/Screenshot-5.png[/IMG]

11-02-2013	#8
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,708	Re: Got Lucky tonite I keep an articulated extending magnet w an LED light built into the head. Perfect for this type of search and rescue mission. __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX

11-02-2013	#9
Bearly Flying Join Date: Dec 2012 Location: Ponoka, Alberta, Canada Posts: 158	Re: Got Lucky tonite "articulated extending magnet w an LED light built into the head." Now that sounds like a useful tool, where did you find it? __________________ 91 ZR-1 Arctic White/Gray 01 C-5 Magnetic Red/Black 85 FJ 1100 (Big Bore kit, Hooligan Bike) 05 FJR 1300 Yamaha (Long Distance, Sport Touring) And a whole whack of RC Planes

11-02-2013	#10
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Got Lucky tonite Stop messing around and get that thing fired up!!! __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode