Pod Gauge Setups - ZR-1 Net Registry Forums

xlr8nflorida · 02-16-2011

I have been wanting to add a few gauges and possibly a shift light (stealth) or maybe on pillar.

I would prefer a custom piece for best appearance however I don't think that is available to us and we have to buy the one that goes over the existing pillar.

The style I want to go with is:

Here are some setups I found interesting: (the bottom one is DDSLT5 - Dwight)

Please post up photos if you have a cool install or can assist.

Also looking for someone who has an extra pillar I can drill up.

Thanks.

tomtom72 · 02-17-2011

I had an idea about the shift light....once.

On a 90 with the original AUAH prom there was a function for the shift light ( upper left perimeter of the tach side of the dash ) and when I put in the AYBK prom the shift light function was deleted.

Sooooo, I was thinking how to get it back. Would it be possible to buy one of those shift light things and use the guts to trigger the dash shift light? I started looking in section 8A and then I felt that this is something I could screw up and burn the harness up so I chickened out.

HAWAIIZR-1 · 01-06-2013

Digging through my stuff today I came across an Autometer dual gauge pillar pod that I bought a few years ago.

I don't have any gauges and thought that I should start looking to add to my projects list.

What other gauges would you guys consider if you were doing dual gauges? I don't feel the need to duplicate anything that I already have on the dash.

My first thougths were air/fuel and fuel pressure as shown, but I really want to get into serious fine tuning and considering Innovate Motorsports meter instead with digital dual reading and dual wideband O2 sensors and that would be mounted elsewhere on the dash.

If not air/fuel, do you think a vacuum gauge is another good choice? This link provides some very good diagnostics with vacuum gauge or does this mostly apply to old school only?

http://www.secondchancegarage.com/public/186.cfm

Thanks for sharing your thoughts.

Craig

GOLDCYLON · 01-06-2013

Maybe a raptor shift light in between the pod?

HAWAIIZR-1 · 01-06-2013

Quote:

Originally Posted by GOLDCYLON

Maybe a raptor shift light in between the pod?

Thanks GC. I already have the harlan shift light in the A/C vents, but that is a nice idea too.

http://www.hashmarks.com/ShiftLight/page11.html

A26B · 01-06-2013

XfireZ51 · 01-06-2013

That's where mine is too!

Uses Diag connector for Power and signal

02-16-2011	#1
xlr8nflorida Join Date: May 2008 Location: USA Posts: 1,096	Pod Gauge Setups I have been wanting to add a few gauges and possibly a shift light (stealth) or maybe on pillar. I would prefer a custom piece for best appearance however I don't think that is available to us and we have to buy the one that goes over the existing pillar. The style I want to go with is: Here are some setups I found interesting: (the bottom one is DDSLT5 - Dwight) Please post up photos if you have a cool install or can assist. Also looking for someone who has an extra pillar I can drill up. Thanks.

02-17-2011	#2
tomtom72 Join Date: Dec 2004 Location: Jacksonville, FL USA Posts: 4,645	Re: Pod Gauge Setups I had an idea about the shift light....once. On a 90 with the original AUAH prom there was a function for the shift light ( upper left perimeter of the tach side of the dash ) and when I put in the AYBK prom the shift light function was deleted. Sooooo, I was thinking how to get it back. Would it be possible to buy one of those shift light things and use the guts to trigger the dash shift light? I started looking in section 8A and then I felt that this is something I could screw up and burn the harness up so I chickened out. __________________ 1990 ZR-1, Black/grey, #2233, stock. ZR-1 Net Reg Founding Member #316 & NCM member

01-06-2013	#3
HAWAIIZR-1 Join Date: May 2010 Location: Japan Posts: 3,586	Re: Pod Gauge Setups Digging through my stuff today I came across an Autometer dual gauge pillar pod that I bought a few years ago. I don't have any gauges and thought that I should start looking to add to my projects list. What other gauges would you guys consider if you were doing dual gauges? I don't feel the need to duplicate anything that I already have on the dash. My first thougths were air/fuel and fuel pressure as shown, but I really want to get into serious fine tuning and considering Innovate Motorsports meter instead with digital dual reading and dual wideband O2 sensors and that would be mounted elsewhere on the dash. If not air/fuel, do you think a vacuum gauge is another good choice? This link provides some very good diagnostics with vacuum gauge or does this mostly apply to old school only? http://www.secondchancegarage.com/public/186.cfm Thanks for sharing your thoughts. Craig __________________ Craig "ZR-1 NO KA 'OI" "ZR-1 ICHIBAN" 1995 #228 Black/Black with Dunn Heads ZR-1 owner since September 2003 ZR-1 Net Registry Founding Member #0074 NCM Lifetime Member #2048

01-06-2013	#4
GOLDCYLON Join Date: May 2007 Location: Peoria, AZ Posts: 9,155	Re: Pod Gauge Setups Maybe a raptor shift light in between the pod? __________________ GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V

01-06-2013	#6
A26B Join Date: Dec 2003 Location: Arcadia,OK Posts: 3,394	Re: Pod Gauge Setups __________________ Jerry Downey JERRYS LT5 GASKETS & PARTS http://www.jerrysgaskets.com 1994 *ZR-1*, Black/Black, Lingenfelter Aerobody, 416cu in, 3.91 gears, coil-over susp, Brembo brakes, etc. 2016 Black-Red, 3LT-Z51 Auto 8-speed.

01-06-2013	#7
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,708	Re: Pod Gauge Setups That's where mine is too! Uses Diag connector for Power and signal __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode