Clutch replacement questions - Page 3 - ZR-1 Net Registry Forums

LGAFF · 07-05-2009

I typo'd I meant Mcleod Flywheel......can I use the Camaro clutch set up with the Mcleod Flywheel?

-=Jeff=- · 07-05-2009

Quote:

Originally Posted by LGAFF

I typo'd I meant Mcleod Flywheel......can I use the Camaro clutch set up with the Mcleod Flywheel?

no
you can use a camaro Disc, but you need the Corvette Pressure plate and throw-out bearing

rhipsher · 07-05-2009

Lee you can use a camaro disk with the ZR-1 clutch/preasure plate and new flywheel but you can't swap a camaro clutch in place of the stock clutch. There will be issues. And I know you don't want issues. So just use a camaro disk or an aftermarket one and your good to go.

LGAFF · 08-02-2009

Well, I found 12mm 1.75 studs at ACE for $2.40 a piece, the trans is lined up on the studs, but still having a hell of a time getting it in the pilot bearing, only about an inch to get the trans flush with the bell housing.

Cannot wait to get the damn thing done.

Kb7tif · 08-02-2009

Quote:

Originally Posted by LGAFF

Well, I found 12mm 1.75 studs at ACE for $2.40 a piece, the trans is lined up on the studs, but still having a hell of a time getting it in the pilot bearing, only about an inch to get the trans flush with the bell housing.

Cannot wait to get the damn thing done.

Hey there. since there in only about an in to go can you maybe start a couple of bellhousing screws and bring the trans in that way, how i did mine, it didnt go so i was going to backed the trans out slid it forward again went right in.
Good luck.

LGAFF · 08-04-2009

The boitch will just not go in, raised the trans, lowered it rocked it back and forth......any ideas?

-=Jeff=- · 08-04-2009

Quote:

Originally Posted by LGAFF

The boitch will just not go it, raised the trans, lowered it rocked it back and forth......any ideas?

you try doing it with the lights out??

WB9MCW · 08-04-2009

TIME FOR THE MURPHY HAMMER

LGAFF · 08-04-2009

Not helping Jeffery .....not helping

PS: please also refrain from the "put some fur around it" comment

QB93Z · 08-04-2009

I had the same problem.

Fill the clutch resovoir and operate the clutch a few times. This will require getting the air out of the lines. Leave the clutch resovoir cap and bellows off while you pump the clutch pedal. After you cycle the clutch a few times the transmission will slide in.

Good Luck!

Jim

07-05-2009	#21
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Clutch replacement questions I typo'd I meant Mcleod Flywheel......can I use the Camaro clutch set up with the Mcleod Flywheel? __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

07-05-2009	#23
rhipsher Join Date: Aug 2008 Location: Houston 90 Red ZR-1 Posts: 2,320	Re: Clutch replacement questions Lee you can use a camaro disk with the ZR-1 clutch/preasure plate and new flywheel but you can't swap a camaro clutch in place of the stock clutch. There will be issues. And I know you don't want issues. So just use a camaro disk or an aftermarket one and your good to go. Last edited by rhipsher; 07-05-2009 at 01:47 PM.

08-02-2009	#24
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Clutch replacement questions Well, I found 12mm 1.75 studs at ACE for $2.40 a piece, the trans is lined up on the studs, but still having a hell of a time getting it in the pilot bearing, only about an inch to get the trans flush with the bell housing. Cannot wait to get the damn thing done. __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

08-04-2009	#26
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Clutch replacement questions The boitch will just not go in, raised the trans, lowered it rocked it back and forth......any ideas? __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359 Last edited by LGAFF; 08-04-2009 at 10:03 PM.

08-04-2009	#28
WB9MCW Join Date: Dec 2003 Location: McHenry, Il. Posts: 6,607	Re: Clutch replacement questions TIME FOR THE MURPHY HAMMER __________________ http://i119.photobucket.com/albums/o...9mcw/SIG-2.jpg http://i119.photobucket.com/albums/o128/wb9mcw/vcm.gif "The Budget should be balanced, the Treasury should be refilled, public debt should be reduced, the arrogance of officialdom should be tempered and controlled, and the assistance to foreign lands should be curtailed, lest Rome will become bankrupt. People must again learn to work instead of living on public assistance." - Cicero, 55 BC " We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution." - Abraham Lincoln

08-04-2009	#29
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Clutch replacement questions Not helping Jeffery .....not helping PS: please also refrain from the "put some fur around it" comment __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

08-04-2009	#30
QB93Z Join Date: May 2007 Location: Westminster, Maryland Posts: 3,689	Re: Clutch replacement questions I had the same problem. Fill the clutch resovoir and operate the clutch a few times. This will require getting the air out of the lines. Leave the clutch resovoir cap and bellows off while you pump the clutch pedal. After you cycle the clutch a few times the transmission will slide in. Good Luck! Jim __________________ If it isn't fun, you aren't doing it right! 1990 Black ZR-1 - sold 1993 Quasar Blue ZR-1 1994 Competition Yellow ZR-1 1995 Dark Purple ZR-1 Maryland State Coordinator WAZOO Member

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode