Clutch replacement questions - Page 2 - ZR-1 Net Registry Forums

LGAFF · 06-27-2009

The car is 16.5" off the ground(rocker cover to gorund).....is that high enough to do the work?

Also found out my knock sensor is off, that might be my performance issue at the track.

WB9MCW · 06-27-2009

Photos of doing the tranny pull >>> http://www.corvetteactioncenter.com/...lutch-job.html

MORE ON TRANNY PULL >> http://www.zfdoc.com/transmission.htm

FOR MY MEGA LINK AND THREAD LIST FOR CORVZ061 (MY BUDDY) FOR ZR-1 MODS AND THINGS TO DO
SEE >>> http://zr1netregistry.com/forum/show...66&postcount=3

Kb7tif · 06-27-2009

While your trans is out pop in a new main seal 6$ (driveshaft). Do yourself a favor drain the transmission fluid first.

rhipsher · 06-28-2009

Photos of doing the tranny pull >>> http://www.corvetteactioncenter.com/...lutch-job.html

Gee! That looks familliar. Hehehehehe!

diamond zr1 · 06-28-2009

16/1/2 inches,on the floor I could not slide under that/get a lift;;;;

Hammer · 06-28-2009

Change the driveshaft u-joints too. Spicer non-greasable if you are racing.

LGAFF · 06-28-2009

Quote:

Originally Posted by diamond zr1

16/1/2 inches,on the floor I could not slide under that/get a lift;;;;

I have the same problem, di#k gets in the way

Trust me if I can get under there at 260lbs.....so can you

LGAFF · 07-05-2009

Since I went with a Mcleod single disk, can I then use a sprung hub out of a 1996 Camaro Z28?

-=Jeff=- · 07-05-2009

Quote:

Originally Posted by LGAFF

Since I went with a Mcleod single disk, can I then use a sprung hub out of a 1996 Camaro Z28?

um, the disc will have the sprung hub..

but if you use a ZR-1 pressure plate and Throw out bearing, then yes you can use the Camaro sprung hub disc

rhipsher · 07-05-2009

Lee the Mcleod disc should have the springs already in it. This is a CenterForce but It should look something like this. Unless you meant your aluminum flywheel.

06-27-2009	#11
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Clutch replacement questions The car is 16.5" off the ground(rocker cover to gorund).....is that high enough to do the work? Also found out my knock sensor is off, that might be my performance issue at the track. __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359 Last edited by LGAFF; 06-27-2009 at 09:01 PM.

06-27-2009	#12
WB9MCW Join Date: Dec 2003 Location: McHenry, Il. Posts: 6,607	Re: Clutch replacement questions Photos of doing the tranny pull >>> http://www.corvetteactioncenter.com/...lutch-job.html MORE ON TRANNY PULL >> http://www.zfdoc.com/transmission.htm FOR MY MEGA LINK AND THREAD LIST FOR CORVZ061 (MY BUDDY) FOR ZR-1 MODS AND THINGS TO DO SEE >>> http://zr1netregistry.com/forum/show...66&postcount=3 __________________ http://i119.photobucket.com/albums/o...9mcw/SIG-2.jpg http://i119.photobucket.com/albums/o128/wb9mcw/vcm.gif "The Budget should be balanced, the Treasury should be refilled, public debt should be reduced, the arrogance of officialdom should be tempered and controlled, and the assistance to foreign lands should be curtailed, lest Rome will become bankrupt. People must again learn to work instead of living on public assistance." - Cicero, 55 BC " We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution." - Abraham Lincoln Last edited by WB9MCW; 06-27-2009 at 09:12 PM.

06-27-2009	#13
Kb7tif Join Date: May 2009 Location: S Nevada Posts: 352	Re: Clutch replacement questions While your trans is out pop in a new main seal 6$ (driveshaft). Do yourself a favor drain the transmission fluid first. __________________ 1995 Convertible Supercharged Auto 1974 454 550hp (avatar car) On the blocks- -Scharger install ! 1992-Zr-1 Sold. Watson Headers Ported Plenum, Housings Random tech cats Fidanza Flywheel Chipped, Relocated Mat Woods 165 stat Borlas, Straights 1996 Lt4 Sold 1994 Lt1 Sold 2004 Z06 Sold AKA** Illenema

06-28-2009	#14
rhipsher Join Date: Aug 2008 Location: Houston 90 Red ZR-1 Posts: 2,320	Re: Clutch replacement questions Photos of doing the tranny pull >>> http://www.corvetteactioncenter.com/...lutch-job.html Gee! That looks familliar. Hehehehehe!

06-28-2009	#15
diamond zr1 Join Date: Sep 2006 Location: diamond lake /washington Posts: 223	Re: Clutch replacement questions 16/1/2 inches,on the floor I could not slide under that/get a lift;;;;

06-28-2009	#16
Hammer Join Date: Apr 2006 Location: Ideho Posts: 2,653	Re: Clutch replacement questions Change the driveshaft u-joints too. Spicer non-greasable if you are racing. __________________ [I][FONT=Comic Sans MS]John Boyd[/FONT][/I] [I][FONT=Comic Sans MS][SIZE=1]Ideho[/SIZE][/FONT][/I] [FONT=Comic Sans MS][SIZE=1][I]2015 ZL1 [/I][I]Camaro #1121 BLACK/BLACK 6 SPD (540 RWHP)[/I][/SIZE][/FONT] [I][FONT=Comic Sans MS][SIZE=1]1991 ZR-1 #458 [COLOR=red]RED/[/COLOR][COLOR=black]BLACK 72[/COLOR]k miles ([B][COLOR=red]SOLD[/COLOR][/B]) 1991 ZR-1 #473 [COLOR=red]RED/[/COLOR][COLOR=black]BLACK [/COLOR]37k miles ([B][COLOR=red]SOLD[/COLOR][/B])[/SIZE][/FONT][/I]

07-05-2009	#18
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Clutch replacement questions Since I went with a Mcleod single disk, can I then use a sprung hub out of a 1996 Camaro Z28? __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

07-05-2009	#20
rhipsher Join Date: Aug 2008 Location: Houston 90 Red ZR-1 Posts: 2,320	Re: Clutch replacement questions Lee the Mcleod disc should have the springs already in it. This is a CenterForce but It should look something like this. Unless you meant your aluminum flywheel. Last edited by rhipsher; 07-05-2009 at 12:11 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode