92 just went kabloom - Page 2 - ZR-1 Net Registry Forums

WB9MCW · 07-03-2009

Boy Gaffer ur having fun now --

Funny how you were just asking abt tranny removal the other day

U must of had a premonition

LGAFF · 07-03-2009

Throw out bearing came apart....

WB9MCW · 07-03-2009

Time to go Fidanza and Ceramic Baby !!!!

XfireZ51 · 07-03-2009

Throw out bearing retaining ring?

LGAFF · 07-03-2009

There were ball bearings inside the bell housing....retaining ring was fine

XfireZ51 · 07-03-2009

Quote:

Originally Posted by LGAFF

There were ball bearings inside the bell housing....retaining ring was fine

Sounds like throwout bearing fell apart.

rhipsher · 07-03-2009

Yep! I knew it. It sounds like yours came apart worse than mine. Picture time.

Also Lee check to see if the clutch fork dug into the bell housing where the slave rod comes through. Because when the throwout bearing breaks and there's no resistance anymore the slave cylinder will binde the clutch fork against the wall and dig into it. A die grinder will smooth it out perfect.

And WB9MCW is right about the Fidanza. If you can affort to dish out $325 on a Fidanza and a good clutch disk or a more high performance clutch then it only makes sense to do it while your at this point. I'm sure glad I did.

LGAFF · 07-03-2009

rhisper, Thanks for all the help...not so bad so far and if I had done it before it would be failrly simple. Having -=Jeff=-, Pete, and Dominic assist has also been a big plus..

Not looking forward to putting the C beams back.

This job is much easier with the headers.....I bet cats get in the way.

rhipsher · 07-03-2009

Quote:

Originally Posted by LGAFF

rhisper, Thanks for all the help...not so bad so far and if I had done it before it would be failrly simple. Having -=Jeff=-, Pete, and Dominic assist has also been a big plus..

Not looking forward to putting the C beams back.

This job is much easier with the headers.....I bet cats get in the way.

Definetely not rocket science. Just allot of manual labor thats all. And it's a hell of allot cheaper than paying a shop to do it thats for sure. All of the chevy dealers around here charge $98 and hour for labor.

rkreigh · 07-05-2009

you are likely done already but the C beam plates make the job much easier and enhance the way the car drives by stiffening up the mounting points on the cbeam

I have a set ready to ship if you need em, $160 shipped out

they really work well and make the job much easier. perfect time to put them in

PM me or email at ron_kreigh@hotmail.com

note there is an _ underscore between ron and kreigh

07-03-2009	#11
WB9MCW Join Date: Dec 2003 Location: McHenry, Il. Posts: 6,607	Re: 92 just went kabloom Boy Gaffer ur having fun now -- Funny how you were just asking abt tranny removal the other day U must of had a premonition __________________ http://i119.photobucket.com/albums/o...9mcw/SIG-2.jpg http://i119.photobucket.com/albums/o128/wb9mcw/vcm.gif "The Budget should be balanced, the Treasury should be refilled, public debt should be reduced, the arrogance of officialdom should be tempered and controlled, and the assistance to foreign lands should be curtailed, lest Rome will become bankrupt. People must again learn to work instead of living on public assistance." - Cicero, 55 BC " We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution." - Abraham Lincoln

07-03-2009	#12
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: 92 just went kabloom Throw out bearing came apart.... __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

07-03-2009	#13
WB9MCW Join Date: Dec 2003 Location: McHenry, Il. Posts: 6,607	Re: 92 just went kabloom Time to go Fidanza and Ceramic Baby !!!! __________________ http://i119.photobucket.com/albums/o...9mcw/SIG-2.jpg http://i119.photobucket.com/albums/o128/wb9mcw/vcm.gif "The Budget should be balanced, the Treasury should be refilled, public debt should be reduced, the arrogance of officialdom should be tempered and controlled, and the assistance to foreign lands should be curtailed, lest Rome will become bankrupt. People must again learn to work instead of living on public assistance." - Cicero, 55 BC " We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution." - Abraham Lincoln

07-03-2009	#14
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,708	Re: 92 just went kabloom Throw out bearing retaining ring?

07-03-2009	#15
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: 92 just went kabloom There were ball bearings inside the bell housing....retaining ring was fine __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

07-03-2009	#17
rhipsher Join Date: Aug 2008 Location: Houston 90 Red ZR-1 Posts: 2,320	Re: 92 just went kabloom Yep! I knew it. It sounds like yours came apart worse than mine. Picture time. Also Lee check to see if the clutch fork dug into the bell housing where the slave rod comes through. Because when the throwout bearing breaks and there's no resistance anymore the slave cylinder will binde the clutch fork against the wall and dig into it. A die grinder will smooth it out perfect. And WB9MCW is right about the Fidanza. If you can affort to dish out $325 on a Fidanza and a good clutch disk or a more high performance clutch then it only makes sense to do it while your at this point. I'm sure glad I did. Last edited by rhipsher; 07-03-2009 at 08:45 PM.

07-03-2009	#18
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: 92 just went kabloom rhisper, Thanks for all the help...not so bad so far and if I had done it before it would be failrly simple. Having -=Jeff=-, Pete, and Dominic assist has also been a big plus.. Not looking forward to putting the C beams back. This job is much easier with the headers.....I bet cats get in the way. __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359 Last edited by LGAFF; 07-03-2009 at 09:11 PM.

07-05-2009	#20
rkreigh Join Date: Jan 2004 Location: Alex VA Posts: 1,087	Re: 92 just went kabloom you are likely done already but the C beam plates make the job much easier and enhance the way the car drives by stiffening up the mounting points on the cbeam I have a set ready to ship if you need em, $160 shipped out they really work well and make the job much easier. perfect time to put them in PM me or email at ron_kreigh@hotmail.com note there is an _ underscore between ron and kreigh __________________ 95 390 LPE ZR1 (505 rwhp) LSV = Lingenfelter Super Vette Twin Turbo 2003 Z06 (800 RWHP)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode