|
11-25-2008
|
#1 |
Join Date: Jun 2006
Location: Thunderbolt, Ga.
Posts: 253
|
ZR1 Front Spindle removal
Hello Everyone,
Over the Thanksgiving holidays I am going to try to remove a front spindle from my 1990 ZR1. I was wondering if there is anything special about the procedure? Any special tools required? If anyone has tackled this I would love some input on the specifics as I do not have a FSM. I did the rear spindle a few days ago and it really was a breeze. I am hoping the front is the same deal. I wish you all a happy Thanksgiving. 
__________________
IT IS THE FATE OF THE INNOCENT TO MEET WITH DEATH!!! |
|
|
|
11-25-2008
|
#2 |
Join Date: Apr 2006
Location: Ideho
Posts: 2,653
|
Re: ZR1 Front Spindle removal
No help here, just wanted to respond. Too many posts go without responses.
__________________
[I][FONT=Comic Sans MS]John Boyd[/FONT][/I] [I][FONT=Comic Sans MS][SIZE=1]Ideho[/SIZE][/FONT][/I] [FONT=Comic Sans MS][SIZE=1][I]2015 ZL1 [/I][I]Camaro #1121 BLACK/BLACK 6 SPD (540 RWHP)[/I][/SIZE][/FONT] [I][FONT=Comic Sans MS][SIZE=1]1991 ZR-1 #458 [COLOR=red]RED/[/COLOR][COLOR=black]BLACK 72[/COLOR]k miles ([B][COLOR=red]SOLD[/COLOR][/B]) 1991 ZR-1 #473 [COLOR=red]RED/[/COLOR][COLOR=black]BLACK [/COLOR]37k miles ([B][COLOR=red]SOLD[/COLOR][/B])[/SIZE][/FONT][/I] |
|
|
|
|
11-25-2008
|
#3 |
|
Guest
Posts: n/a
|
Re: ZR1 Front Spindle removal
You just replacing the hub, or are you doing UBJ and LBJ?
|
|
|
|
11-25-2008
|
#4 |
|
Join Date: Aug 2005
Location: Lancaster, PA
Posts: 147
|
Re: ZR1 Front Spindle removal
Easier than the rear which you did. No special tool is needed. I assume you're not changing ball joints.
|
|
|
|
|
11-26-2008
|
#5 |
|
Join Date: Jun 2006
Location: Thunderbolt, Ga.
Posts: 253
|
Re: ZR1 Front Spindle removal
Exactly what I wanted to hear. Thankyou for the info. I am not messing with the ball joints. Instead I am sending my spindles to Aerospace Components where they will be used to fab up caliper brackets and rotor hubs. I already have the calipers and rotors from a Mustang project that I never got around to so hopefully Ill have a custom brake upgrade for not that much $$$. The calipers are nice 4 piston units and the rotors are small diameter so I can fit 15" drag wheels all around. Should be nice, + quite an improvement over stock despite the rotor diameter. I am swapping to manual M.C. as well and replacing all the lines. I'm certain my OEM brakes were in perfect working order but they just dont slow the car down fast enough. Ironically the ZR1's 13" PBR setup is the same as the Mustang Cobra's PBR brakes I originally bought the A.C. kit to replace. The PBR floating caliper setup is lacking in my world. I dont like it.
__________________
IT IS THE FATE OF THE INNOCENT TO MEET WITH DEATH!!! |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
