|
10-14-2008
|
#21 |
  
Join Date: May 2007
Location: Peoria, AZ
Posts: 9,119
|
Re: Engine Parts
Did you talk to Jeff Flint AKA Jeffvette? $1200 is insane for a set of bolts!!!
__________________
GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director  91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V |
|
|
|
10-14-2008
|
#22 |
|
Guest
Posts: n/a
|
Re: Engine Parts
M14 x 1.5 x 220mm
Last edited by Jeffvette; 10-14-2008 at 08:49 PM. |
|
|
|
10-14-2008
|
#23 |
 
Join Date: Apr 2007
Location: Northern VA
Posts: 2,651
|
Re: Engine Parts
Parts book specifies 14X1.5X80
Can someone confirm this is the correct size head bolt? Do the factory LT5 head bolts have any special feature? Fastenal has 10.9 grade bolts listed in this size. |
|
|
|
|
10-14-2008
|
#24 |
|
Join Date: Sep 2005
Location: Washington
Posts: 952
|
Re: Engine Parts
I can tell you it's NOT 80mm. Thats only 3.149 inch. The bolts go from the top of the head to the bottom of the block.
|
|
|
|
|
10-14-2008
|
#25 | |
 
Join Date: Dec 2003
Location: Arcadia, OK
Posts: 3,403
|
Re: Engine Parts
Quote:
Thread length is 62mm. Bolts must also have the flat ground, hardened washer. Obviously the washers can be reused, but if you have NO head bolts, the washers will be required also. Bolt head has an integral flange under the hex. I would imagine the prudent thing to do would be to send a stock head bolt to ARP to copy the configuration. I'll go so far as to say the result will be sticker shocking from ARP as well. It's a really big bolt.
__________________
Jerry Downey JERRYS LT5 GASKETS & PARTS http://www.jerrysgaskets.com 1994 ZR-1, Black/Black, Lingenfelter Aerobody, 416cu in, 3.91 gears, coil-over susp, Brembo brakes, etc. 2016 Black-Red, 3LT-Z51 Auto 8-speed. |
|
|
|
|
|
10-14-2008
|
#26 | |
|
Guest
Posts: n/a
|
Re: Engine Parts
Quote:
M14 x 1.5 x 220mm |
|
|
|
|
10-14-2008
|
#27 |
Join Date: Mar 2007
Location: Crystal Lake, IL
Posts: 7,180
|
Re: Engine Parts
ARP sent a form to fill out, they want actual measurements including gasket material etc. They stated they may have otherbolts that match.
PDF file is too big to post here. I can't believe these frggin head bolts are more than I paid for a shortblock. LGAFF 92 ZR1 #234 I wonder what ACE hardware has in stock. 
|
|
|
|
|
10-14-2008
|
#28 |
|
Join Date: Sep 2005
Location: Washington
Posts: 952
|
Re: Engine Parts
Stroker Crank.......... check
JE pistons................check Oliver rods...............check SGC Cams................check . . . . Made in China bolts to hold it all together......... 
|
|
|
|
|
10-15-2008
|
#29 |
 
Join Date: Aug 2006
Location: Edmonton, Alberta or Phoenix, Arizona
Posts: 2,736
|
Re: Engine Parts
yup...that's what you gotta have is the form. got a bunch here at all times, unfortunatly. the main measurment they will want above all else is U.H.L. (under head lenght). also, i always shoot for maximum thread lenght in(to) an aluminum block.
|
|
|
|
|
10-15-2008
|
#30 |
|
Join Date: Jan 2004
Location: Alex VA
Posts: 1,080
|
Re: Engine Parts
guys,
Ron and Randy Woods ZR1 Specialty Products make head studs that work just great they worked with ARP to design just the right stuff and are both cheaper and superior to stock give em a shout |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
