Next Mod to my Z.....

[Paul Workman]

Originally Posted by -=Jeff=-

with the included pieces my Borla should bolt right up. Now at the time I install, if I have the extra $$ I will by the 3" Magnaflow system like Dominic..

Well I think I will, I need to hear it in Dom's car first, verify the resonance is low like he says

Jeff! We're in the same spot there. I don't yet have the P&P done (but winter is coming!), but I do have the SW 3" headers to go to the Borla. I'm looking forward to what fruits that brings! I definitely will need Doms or Marc's help w/ a chip tho when I get done. (Mine appears to be a bit lean - perhaps the chip was not changed after the Borla was added...I dunno.) And, like you, I'm interested to see how Dom's Magnaflows work and sound!

P.

[-=Jeff=-]

Originally Posted by Pete

Congrats Jeff
Those look like they were on a later Z the early ones had the 3 bolt flange (right side) which i would suggest going that route easier to R&R the exhaust.

When is the install party?
I have a few beers in the garage cooler somebody has to come over and drink them before they expire.

Jeff,let me know if you need a hand with the install.
Can you say 120MPH

Pete

I need to get the install pieces and then figure what works for you.. Al said a lift make life easier.. I think this should bolt right to Cat back I have too.. I think

[z proud]

Originally Posted by USAFPILOT

Does anyone have the full setup from Stainless works?

Dave has the full setup

I have stainless works headers and corsa

[USAFPILOT]

I'd like to see/hear dave's setup

[-=Jeff=-]

Originally Posted by Pete

Congrats Jeff
Those look like they were on a later Z the early ones had the 3 bolt flange (right side) which i would suggest going that route easier to R&R the exhaust.

When is the install party?
I have a few beers in the garage cooler somebody has to come over and drink them before they expire.

Jeff,let me know if you need a hand with the install.
Can you say 120MPH

Pete

Hey Pete, I might need a hand.. I will give you a call this week.

I am guessing you are talking about the slip fit? I am thinking of getting the Ball Flanges like I used on my 89. I am also now considering the Magnaflow exhaust like Dominic has, I road in his car yesterday and there is barely any resonance with the exhaust

[Paul Workman]

Originally Posted by -=Jeff=-

I am also now considering the Magnaflow exhaust like Dominic has, I road in his car yesterday and there is barely any resonance with the exhaust

Good to know. I'd like to here 'em too before I take the plunge. Thanks for the post, Jeff.

P.

[RICKYRJ1]

Originally Posted by z proud

Dave has the full setup

I have stainless works headers and corsa

Are you running cats w/the headers?

[RICKYRJ1]

Originally Posted by jonszr1

i just got installing stainless works headers on my 92 .they made a nice difference. had to extend the wiring on passenger o2 sensor bought the bolts local . spent 25bucks on the whole deal.car has corsa exhaust and allways thought it too quiet. now it has the perfect sound and no cabin drone. quiet when cruzing and just perfect amount of noise when floored

Are you running cats w/ the headers?

[ZZZZZR1]

Originally Posted by USAFPILOT

I'd like to see/hear dave's setup

Full setup is really mean (agressive exhaust) and powerful. Everyone who listened to it @ Carlisle thought it was incredible....

I just purchased new Tips from SW (old tips were cheezy) and can't wait to install them.

Also installed 4:10 gears sunday (thanks to the VA boyz! You know who you are)... Between the headers / exhaust / chip (haibeck) and the gears, my car runs LIKE A RAPED APE!!!!!!

[jonszr1]

yes i have the stainless works bullet cats that came with the headers. it made the car just loud enough when you open her up . hope to try it out at the strip fri . they have a tand t on fri at sacramento , thats if i can get the rearend changed out on the blk car . i have a bearing going bad on the passenger side yoke on the white car .