![]() |
#61 |
![]() Join Date: Apr 2012
Location: Austin, TX
Posts: 54
|
![]()
I realize this is an old, old thread but having been chasing a "rough idle" in my '94 coupe (not the ZR-1) just ran across this and it was the silver bullet or at least one of three; the canister was bad, the line was clogged with charcoal pellets (blew those out with compressed air) and I replaced the purge solenoid while I was at it not knowing what was in it. All runs as it should now.
Many, many thanks! John PS The car gave me a BIG clue at the start of my hunt as opening the gas cap after a drive of any length (especially when it was a hot day) would release a tremendous "WHOOSH" sound but checking the Corvette Forum I found threads suggesting that was normal. In fact, it's not, just a symptom of a defective canister. |
![]() |
![]() |
![]() |
#62 |
![]() Join Date: Feb 2006
Location: San Antonio area
Posts: 1,177
|
![]()
The canister on my 91 leaked enough fumes to cause the vehicle to flunk the Illinois emissions test in 2002 - the test used a pickup hose at each exhaust pipe and the RH hose detected the unburned HC content. Many dollars were spent trying to pass the test until the defective canister was discovered. What I'd like to know is which hose(s) do you inspect for carbon granules - I read the whole thread and nobody really answered that question ...
__________________
“Buy the best example of what you want, and pay whatever it takes. That way, you cry only once.” ~ Bruce Meyer |
![]() |
![]() |
![]() |
#63 |
![]() Join Date: Apr 2012
Location: Austin, TX
Posts: 54
|
![]()
I have not looked at the FSM for my ZR-1 but on my '94 the hose that can become plugged with carbon granules is the one that runs from the canister to the engine (the vacuum pulls the granules from a defective canister). The other hose, from the tank to the canister, is not subject to the problem as the vacuum is pulling the fumes from the tank to the canister. John
|
![]() |
![]() |
![]() |
#64 |
![]() Join Date: Sep 2012
Location: Rockwall, Tx
Posts: 1,504
|
![]()
Hey, John. Good to see you hangin' around.
Thanks for digging this old thread up. After seeing it I was reminded that the PO of my car had mentioned something about replacing the canister back by the right rear wheel. I didn't have a clue what he was talking about so I just filed it somewhere in my brain. So, after going through all the parts I got with the car there it was. A brand new canister still in the box. I might as well put it on since I have it and it is 20 years old now. Many thanks, my friend!
__________________
_________________ 1994 AB/Grey #141 430 RWHP/392 RWTQ FBI Lyposuction / Secondaries relieved of duty / SW Long Tube Headers / Corsa Exhaust / FIC SS Injectors / MSD Coils / Lightweight Pulleys / Corey tuned B & M Shifter / Aluminum Flywheel / Samco Hoses / Shelby Series One's / C4 No Flex Frame Stiffener BBC - Bling By Carter: Custom ZR-1 Center Caps / Custom Plenum Plate / Air Box Knobs / TB Cover / Oil Filter Cover |
![]() |
![]() |
![]() |
#65 |
Join Date: Aug 2005
Location: Scottsdale, AZ
Posts: 2,446
|
![]()
I had trouble with mine, no longer, its gone, most of our cars experience the same problems
|
![]() |
![]() |
![]() |
#66 |
![]() Join Date: Sep 2012
Location: Rockwall, Tx
Posts: 1,504
|
![]()
You "kludged" it? I didn't realize you could do that. What's the work around? It doesn't throw any codes?
__________________
_________________ 1994 AB/Grey #141 430 RWHP/392 RWTQ FBI Lyposuction / Secondaries relieved of duty / SW Long Tube Headers / Corsa Exhaust / FIC SS Injectors / MSD Coils / Lightweight Pulleys / Corey tuned B & M Shifter / Aluminum Flywheel / Samco Hoses / Shelby Series One's / C4 No Flex Frame Stiffener BBC - Bling By Carter: Custom ZR-1 Center Caps / Custom Plenum Plate / Air Box Knobs / TB Cover / Oil Filter Cover |
![]() |
![]() |
![]() |
#67 |
Join Date: Aug 2005
Location: Scottsdale, AZ
Posts: 2,446
|
![]()
That's a ? for Marc, no emissions needed here
|
![]() |
![]() |
![]() |
#68 | |
![]() Join Date: Apr 2012
Location: Austin, TX
Posts: 54
|
![]() Quote:
Hi David - Hadn't seen your dyno numbers before (430 RWHP/392 RWTQ). Very impressive. John |
|
![]() |
![]() |
![]() |
#69 |
![]() Join Date: Apr 2004
Location: Atlanta, GA
Posts: 2,169
|
![]()
Just a Question, I know this is after the fact but would be insurance to keep the charcoal bits out of the line could you add a small filter on the out going line? solid rock one like you use on an aquarium or paper fuel line filter?
__________________
Steve 1990 Steel Blue/Black #2355 1990 Red/Red #1473 1991 Quasar /Black #118 Sold 1991 Turquoise/Black #766 Parted Out 1993 Yellow/White #179 Sold 1990 Black/Gray #1361 Headers/4:10s Sold |
![]() |
![]() |
![]() |
#70 | |
Join Date: Jun 2009
Location: I live at Devens, one run at a time
Posts: 454
|
![]() Quote:
I've noticed a fuel smell at the rear before and I've been fighting an odd up-idle for a long time. Me thinks I'm in this club too, but it sounds like the purge valve is under the plenum?? I was really hoping it'd be easy to get at so as to blow out any crud. Yikes, - Jeff |
|
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|