![]() |
#1 |
Join Date: Feb 2012
Location: Albuquerque, NM
Posts: 34
|
![]()
I'm a new member here but a long time member of the other forum under the same user ID.
I wasn't looking for a Z but last summer a 1990 with 13,400 miles came along through a co-worker and at the price I couldn't say no. I haven't done much with it until recently. The injectors were original (well, most of them) and the vacuum pump was running full time, so I knew a plenum pull to fix the vacuum leak and replace the injectors was in order. I ordered new stainless injectors from Jon at FIC. That plenum pull project is now getting out of hand. The crankcase breather cover was obviously leaking oil, so I got the gasket for it and removed it. To remove it I removed the serpentine belt, moved the AC compressor, and removed the alternator. The alternator had a bearing that was failing so I had it rebuilt. Dropped a small rubber hose into the crankcase so I had to remove the oil pan, but that was okay since it was leaking oil too so I ordered the gasket from Jerry's. The front right side of the engine is very oily, so I removed the oil filter housing to replace the gasket. Also ordered the dreaded oil level sensor that commonly fails and leaks lots of oil, so I'll replace that just because it's so much easier to get to now. The oil cooler lines look fine. So now the plenum is off, injectors and fuel rail are out, alternator is out, AC compressor is out of the way, oil pan is off, serpentine belt tensioner is out, and oil filter housing has been uninstalled from the engine (oil cooler lines are still connected, and I wanted to leave them since they don't appear to be leaking). My question is, should I do anything else-- replace any parts, tighten any bolts or screws, clean anything, etc.-- while everything is apart? How about the water pump? There's no problem with the water pump and the car only has 13,400 miles and a new water pump is $300+, but it's right there and would be easy to do. Is this something that commonly fails, or should I just leave it alone and expect to get another 50,000 or 80,000 miles out of it? And please don't tell me to port the plenum and injector housings, I don't need to spend any more money on this thing! |
![]() |
![]() |
![]() |
#2 |
![]() ![]() ![]() Join Date: May 2007
Location: Peoria, AZ
Posts: 9,154
|
![]()
Plugs and wires come to mind while you are there
__________________
GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director ![]() 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V |
![]() |
![]() |
![]() |
#3 |
Join Date: Feb 2012
Location: Albuquerque, NM
Posts: 34
|
![]()
Plugs are pretty easy to do anytime, right? And wires are original but look to be in new condition with 13,400 miles. How about coils?
|
![]() |
![]() |
![]() |
#4 | |
![]() ![]() ![]() Join Date: May 2007
Location: Peoria, AZ
Posts: 9,154
|
![]() Quote:
to the plenum. The coils your call due to age but they an easy $50 a piece so .... Again your call
__________________
GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director ![]() 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V |
|
![]() |
![]() |
![]() |
#5 |
Join Date: Mar 2010
Location: Fort Worth, TX
Posts: 396
|
![]()
Leave the water pump alone
|
![]() |
![]() |
![]() |
#6 |
![]() ![]() ![]() Join Date: May 2007
Location: Peoria, AZ
Posts: 9,154
|
![]()
__________________
GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director ![]() 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V |
![]() |
![]() |
![]() |
#7 |
Join Date: Mar 2009
Location: Orlando, FL
Posts: 1,828
|
![]()
Wires will age, regardless of mileage, due to exposure to air and heat. I'd suggest removing your OEM wires, toss them on ebay for the NCRS types who want the "LT5" lettering, and put a nice fresh set of wires on for $60 or so.
__________________
2004 Z06/Z16 LeMans Commemorative Edition 1991 ZR-1 #302 White/Gray (sold) 1991 ZR-1 #1147 Red/Saddle (sold) |
![]() |
![]() |
![]() |
#8 |
![]() Join Date: Aug 2011
Location: Evergreen, Co.
Posts: 346
|
![]()
Be sure to tighten the The Oil Pressure Regulator Cover. Often accompanying an oil pan gasket leak, is leakage from the little cover that is located on the right side front just above the oil pan flange. This description is from Marc Halbec's article: Finding and Fixing Oil leaks on the LT5 Engine - "The cover is often found to be loose. The little cover can’t be seen when the engine is installed in the car. To reach it, I like to jack up the right front of the engine and reach down from the top. It’s still difficult to see. I often tighten it by feel. The two fasteners
with 8 mm heads need to be tightened."
__________________
Bert Rankin 1991 ZR1 Steel Blue / Steel Blue #1029 Haibeck chip, slotted rotors, camber brace, C-beam plates, OBX exhaust, Nitto NT555 tires [SIGPIC][/SIGPIC] Last edited by SteelBlueZR1; 03-03-2012 at 12:24 AM. |
![]() |
![]() |
![]() |
#9 |
![]() Join Date: Feb 2011
Location: San Marcos CA
Posts: 1,802
|
![]()
My experiences: '91 car w 27k miles- now at 33k miles 13 months later.
Driving the car has been the best thing for it. -bad injectors replaced -leaky oil cooler lines replaced -radiator and oil cooler cleaned up from said leaky oil mess -new thermostat installed since I had all that stuff apart -slight alternator bearing squeak sometimes, I kind of wish I took care of it, but i bet it last for 3 more years. -$200 belt tensioner replaced. - ported I/H and plenum (twice)...took care of minor oil leak on I/H gasket from gaff on first attempt. - new spark plugs and compression check for piece of mind (easy). - water pump fine so far...been out-of-state twice and been on 4 different vette runs in the local mountains in SoCal. AAA not required. original wires are fine. pulled the plenum 3 times now- you know there will be a 4th. - a bunch of other stuff not related to the engine $$$- car is nearly tip-top, but damn...went over budget. Drove it to work on Wednesday- got comments once again- Not the same type like the C6 comments either. |
![]() |
![]() |
![]() |
#10 |
Join Date: Feb 2012
Location: Albuquerque, NM
Posts: 34
|
![]()
Wow, thanks for all the comments! I'll happily leave the water pump alone. I'll definitely tighten the oil pressure regulator cover, and I'll think about the wires and coils. Not that I want to do it again, but after this project a simple plenum pull should be easy if I did have to do wires and/or coils!
|
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|