Rattle Can Engine Refinish.

[We Gone]

This is my 93

So after reading about this for months I thought it was time to give it a try. I am going to preform this without removing the cam covers or injector housings. I will post pics as I go. Hopefully you guys will enjoy my redneck backyard job. I am using the paint Jerry sells, great paint covers very well. Thanks Jerry for your help time and parts enjoyed our conversation.

Why?
A. I had redone the top of the TB and it did not match.
B. I had Dave M. sign my original plenum at the gathering so I was going to replace it anyway so I could save it.
C. Why not.

Details of what I did and used. I will not get into the details of pulling parts as most of you know or have done that part, Plus we have many guides on it already.

Materials from Jerry's Gaskets
1. Plenum, throttle body, horn and EGR pipe gaskets, a few other miss. parts I replaced while had I things apart.
2. Paint 2 cans http://www.jerrysgaskets.com/paint-l...ish-90-95-6e3/
3. Lots of blue painters tape, cover paper, scotch-brite (fine) 800 wet dry paper, foam (to stuff in tight spots) De-greaser.
4. Thermal compound (for electronics under plenum) Dielectric grease for plugs.http://www.newegg.com/Product/Produc...-080-_-Product
5. Gaskets Plenum http://www.jerrysgaskets.com/gasket-...or-90-95-11b3/ TB http://www.jerrysgaskets.com/gasket-...dy-90-95-11d9/ for 93-up EGR http://www.jerrysgaskets.com/gasket-...pe-93-95-11d9/ Cam cover PVC lines http://www.jerrysgaskets.com/seal-se...be-90-95-11c3/
6. Cam cover emblems http://www.jerrysgaskets.com/emblem-...ver-91-95-7b1/

Parts I removed.
1. Plenum and related parts.
2. ASR box, crankcase breather tubes to cam covers.
3. AC compressor and Alt. (just moved them out of the way)
4. removable part of the AC box for access to right side.

1. Cleaned everything to be painted or taped with de-greaser scuffed all surfaces to be painted with scotch-brite. Cleaned all aluminum piping with scotch-brite. Label an bag parts and screws. You will be surprised at how ruff the castings are if you want a show finish you will have to do some heavy sanding and I would not recommend doing it with the parts on the car. Take pictures of how things are routed for re-install.
2. Tape and cover up, this took the longest the better you tape the better the outcome. I used some 1/2 foam to stuff between the injector housings and heads plus anywhere else I could that was to tight to tape.
3. Painted using 3 coats waiting 24 hours between coats and sanding with 800 wet/dry paper.
4. Each coat was done with 2 very light sprays 15min. apart than a heaver coat looking for a good shine, just don't let it run. wait 24hrs scuff with 800 wipe down with paint prep. Did this 3 times.
5. Waited several days before putting everything back so the paint would dry. Be very careful of painted surfaces unless you have a heat lamp to help harden the paint. I kept them covered until I was done assembling.
6. I used Paul's suggestion to do the lettering. This part worried me most. I did ok, I wish someone would make a tape on stencil so you could spray them.
7. After I assembled and restarted the car let it warm up until the fans cycled to get the paint hot so it would set well. Than took it for a 30 mile drive stopping a few times to check on everything.

I found a replacement plenum (Thanks Pete)
The replacement Plenum.


What I started with. Had a few stains and the TB was in bad need of clean-up.


After cleaning with a cleaner wax it did turn it a shade darker but did a good job. as you can see the TB does not match after cleaning and painting, and of course the replacement plenum will not. This Plenum will become wall art.


After a good de-greasing/sanding 1st coat of paint, will sand with 800 and put on a 2nd and 3rd coat.


On to the hard part. What a mess started sanding and cleaning.




Will post up more as I get things done.

All comments and suggestions welcome, not sure how I will do the lettering just yet.