ZR-1 Net Registry Forums  

Go Back   ZR-1 Net Registry Forums > C4 ZR-1 > C4 ZR-1 Technical Postings

Reply
 
Thread Tools Display Modes
Old 06-01-2006   #1
bobbyhi
 
bobbyhi's Avatar
 
Join Date: Jul 2005
Location: Mendota Heights, MN. 55120
Posts: 984
Default Brake problem

Well, here we go guys. I have a terrible squealing coming from my front right brake. Squeals constantly when heated up (I'm sure from expansion). I put new slotted and drilled rotors on last winter for a little "bling". I had new pads done just last fall so the pads were OK. I just took off the pads and replaced the brackets, retainers, pads, etc. but to no avail. Pretty sure this is a minor item to fix but I must be overlooking something. Any suggestions would be helpful. I have the C5 upgrade on the front. The squealing noise is very annoying and is there even when the brakes are not applied. The left front is fine.................
__________________
Bob Anderson
1990 #2405 White/Gray
Haibeck chip,4:09 gears,Power Effects Exhaust,5 spoke chrome,C5 brakes,49th Street rockers,K&N,Hurst,Headers,Upper & lower ported

Minnesota State Director
Founding Member #19
bobbyhi is offline   Reply With Quote
Old 06-02-2006   #2
tomtom72
 
tomtom72's Avatar
 
Join Date: Dec 2004
Location: Jacksonville, FL USA
Posts: 4,645
Default Re: Brake problem

Hi Bob,

Jez you did almost everything except replace the caliper! Is it possible that the left caliper's piston is slightly stuck? Do our Z's use sliding calipers or do we have two piston calipers? Sorry I don't even know...I never looked

The only other thing would be the wheel bearing assembly, that's all that's left? Unless the dust shield is hitting something...if we even have dust shields? There are no marks on the wheel or the rotor that would indicate something rubbing?

Do the brakes work normally? Ya know, no pulling & they work...stop straight, right?

Sorry...I'm a big help, ain't I! You probably tried all this obvious stuff. Wish I had better suggestions. I'd like to know what's up when you find it!

Tom
__________________
1990 ZR-1, Black/grey, #2233, stock. ZR-1 Net Reg Founding Member #316 & NCM member
tomtom72 is offline   Reply With Quote
Old 06-02-2006   #3
ZR1 MK
 
Join Date: Aug 2005
Location: NY
Posts: 143
Default Re: Brake problem

Did you lube the caliper pins and are they operating (sliding) properly? If so, the pistons would be the next item to check.
__________________
Mike
427 cu in LT5
[URL="http://zr1mk.weebly.com"]http://zr1mk.weebly.com[/URL]
ZR1 MK is offline   Reply With Quote
Old 06-07-2006   #4
bobbyhi
 
bobbyhi's Avatar
 
Join Date: Jul 2005
Location: Mendota Heights, MN. 55120
Posts: 984
Default Re: Brake problem

Took the caliper off and noticed that the rotor was rubbing against one of the calpier clips. Used my dremel to shave it down a bit and put a little silicone on the end and the noise is gone. Thanks for the help. It always amazes me that a 5 cent part can cause so many problems..........
__________________
Bob Anderson
1990 #2405 White/Gray
Haibeck chip,4:09 gears,Power Effects Exhaust,5 spoke chrome,C5 brakes,49th Street rockers,K&N,Hurst,Headers,Upper & lower ported

Minnesota State Director
Founding Member #19
bobbyhi is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:43 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ZR-1 Net Registry 2020